您要查找的是不是：
- Reinstall turn indicator assembly. Scale retaining ring should be hand-tight Do not overtighten. 重新安裝旋轉指示器總成?？潭裙潭ōh(huán)應該用手緊固。不要過緊。
- The reasearch and development of ESR procoss for Cr18Mn18N steel used for the generator retaining ring was described. 闡述Cr18Mn18N發電機護環用鋼電渣重熔技術的開發研究工作。
- Loosen scale retaining ring and remove turn indicator assembly. It is not necessary to change the memory set point. 松開刻度固定環，拆卸旋轉指示器總成。不需要改變記憶設置點。
- The (3) flexible retaining ring provides a complementary seating pressure on the disc. (3)柔性固定環在閥瓣上提供補償性閥座密封壓力。
- This article has described expanding method for repairing the concave retaining ring caused by the hydraulic bulging. 詳細介紹了用擴沖法對液壓脹形出現凹形的護環進行修復的方法。
- To meet the requirements of new assembly procedures of wheel sets,the wheel tyre retaining ring roller mills for locomotives were developed. 為適應輪對新的組裝工藝要求 ,研制了機車輪箍扣環滾壓機。
- We present a FEM method for forecasting the suitable pressure on the retaining ring,which is critical in manufacturing good quality wafers. 在晶圓外部施加保持環可以把晶圓中心處和邊緣處的拋光墊壓平到一致高度,克服晶圓邊緣的"過磨"現象。
- Pressure Seal ? uncomplicated design has segmented retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum bonnet seal. 壓力密封?結構簡單，分段扣環，鍍銀低碳鋼墊圈，有助于拆卸和最大限度的閥帽密封。
- The unknown powder adhering to the retaining ring of a 600 MW generator rotor was characterized and analyzed by SEM, EDS, Raman spectroscopy, XRD, FTIR and TGA. 摘要利用掃描電鏡、能譜儀、X射線衍射儀、激光拉曼光譜儀、傅立葉紅外光譜和熱分析儀對600MW發電機轉子端部護環表面不明粉末進行表征和分析。
- A special retainer ring holds the two sealing ring faces together. 一個特殊的固定環將密封環的表面靠在一起。
- According to the problems encountered during production, the retaining ring expansion and wedge reaming were modified, and it will have an important significance in improving production l... 圍繞生產中出現的問題,提出了改進護環液壓脹形和楔塊擴孔的措施。
- This paper discusses a few of shapes of retain ring after hydraulic expansion, and uses the e-lastic -plastic finite element method to analyses the influencing factors of the shape. 介紹了護環外補液液壓脹形后護環成形形狀的幾種類型,論述了采用彈塑性有限元法分析產生這幾種形狀的影響因素,對護環的生產具有一定的指導作用。
- A stranger plucked at my sleeve as I was leaving. 我剛要離去，一個陌生人拽我的袖子。
- The die and eqiupment of internal pressurized expanding retaining rings and double cone wedge-reaming die were also studied. 對內增壓擴脹護環的裝置和雙錐面楔塊擴孔模具進行了研究。
- A seam broke open at the sleeve. 袖子上接縫處裂開了一點。
- His elbow was poking through his torn shin sleeve. 他的肘從襯衫的破袖子中露出。
- She pulled his sleeve to get his attention. 她拉他的袖子以引起他的注意。
- She sewed up the rip in his sleeve. 她縫好了他衣袖上的裂口。
- retaining ring for shaft shoulder 軸肩擋圈
- She could knit a torn sleeve up. 她能織補撕破的袖子。
