您要查找的是不是：
- Breaking Strength The amount of force needed to break a wire or fiber. 斷裂強度將電線或電纜折斷所需施加的壓力。
- The breaking strength and elongation decreased as the degree of oxidation of cotton fiber increased. 氧化棉纖維的斷裂強度和斷裂伸長率隨氧化程度的提高不斷降低。
- The breaking strength and elongation decreased as the degree of oxidation of cotton fiber i... 氧化棉纖維的斷裂強度和斷裂伸長率隨氧化程度的提高不斷降低。
- The melting point of the fiber was decreased and the breaking strength and birefraction were decreased to a minimum first- ly and then incr. 隨著拉伸溫度的提高,纖維的熔點降低,斷裂強度和雙折射率則先降低后升高,出現最低值。
- The properties including bulging rate,breaking elongation rate and breaking strength of the jute fiber were tested under the different conditions. 分別測定了不同工藝條件下黃麻纖維的膨化率、斷裂伸長率、斷裂強力的變化。
- The xerothermic properties of vinylon-milk protein fiber were studied,including shrinkage,whiteness,breaking strength,weight loss and dyeing behaviors. 研究維綸基牛奶纖維紗線經不同溫度干熱處理后,紗線收縮率、白度、斷裂強力、失重率以及染色性能的變化。
- Used to determine the tensile breaking strength, extension at break of single yarns such as cotton, wool, linen, silk, chemical fiber and so on. 用于測定棉、毛、麻、絲、化纖等單根紗線的抗拉斷裂強力、斷裂伸長。
- Used for measure breaking strength, elong rate of all kinds of fibre materials. 用于測定各種材料的機織物、非機織物的斷裂強力、斷裂伸長率。
- Used for measure breaking strength,elong rate of all kinds of fibre materials. 用于測定各種材料的機織、物非機織物的斷裂伸長率。
- The paper mainly studied the air - jet textured processing for twisted glass fiber yarn, and analysed the effects of the chief parameters on the texturing and breaking strength of the textured yarn. 主要研究玻璃纖維有捻長絲紗的變形制造工藝及工藝參數對變形紗變形效果和斷裂強度影響。
- When the fibers broke, fiber ends were mangled and frayed. 纖維斷裂時，纖維端部相互糾纏并有擦散現象。
- Bacterial enzymes are also preferred for the desirable end product qualities of porosity and breaking strength. 細菌性酶也適于生產多孔性及易碎的產品。
- Breaking strength: The quality of paper by specifying its breaking length in metre. 裂斷強度:以紙張的裂斷長(米)來表達紙張品質。
- A meso mechanical model is developed to describe the longitudinal stiffness reduction and thermo dilatation variation of the composites caused by fiber breaking or fiber peeling o. 借助細觀力學模型,研究了纖維斷裂和剝離對宿主材料剛度和熱膨脹系數的影響,并給出了相應的數學表達式。
- Choosing raw materials, spunlaced process properly may improve product cross breaking strength effectually. 選擇適當的原料、水刺工藝參數可有效地改善產品的橫向斷裂強力。
- The writer explained that cross lapping and impregnated method may improve product cross breaking strength. 說明了采用交叉鋪網、浸膠的方法可大大提高產品的橫向斷裂強力;
- In this paper,the methods are discussed on improvement breaking strength of synthetic libers in processing stage. 根據合成纖維生產工藝過程,分析了合成纖維斷裂強度提高的途徑。
- The breaking strength of cotton fabric will drop evidently both in warp and weft after anti crease finishing. 全棉織物經免燙整理后,其經緯向斷裂強力明顯下降。
- Moreover,the relation between AE signals and the failure processes of FWC from matrix cracks,delaminations,fiber breaks to burst with the water pressure increasing is analyzed. 分析了隨著水壓增加從基體開裂、層間分層及纖維斷裂到最終破壞與聲發射信號的關系;
- There are changes in mechanical properties of the fabric such as weight, thickness, stiffness, permeability, or breaking strength and elongation. 有織物機械性能的改變，諸如重量，厚度，硬度，透氣，斷裂強力和伸長度等性能的改變。
