您要查找的是不是：
- Remove all weld splatter and burrs. 所有焊縫必須焊透.
- A honeycomb sandwich panel inside and an aluminum cladding outside for the ideal combination of solidity and lightness, coldness and heat. 內有蜂窩夾心板，外包鋁質覆層，乃是堅固性與質地輕盈之完美結合，又使冷熱合為一體。
- The low-velocity impact response of Nomex honeycomb sandwich plate was investigated theoretically and experimentally. 給出了基于Mindlin 板理論并考慮到夾芯板上下纖維增強層板在撞擊時變形不同的用于撞擊動響應計算的分析模型。
- The roll-bonding technology of stainless steel/3003 aluminum alloy honeycomb sandwich panel was studied. 研究了采用軋制復合方法生產不銹鋼-3003鋁合金蜂窩夾芯板的工藝。
- Aluminium honeycomb sandwich panel has high strength, light weight ,so it is widely used in many products. 鋁蜂窩夾芯板由于其強度好,重量輕,正廣泛用于許多制件上。
- In this paper,the dynamic analysis of the carbon fiber honeycomb sandwich structure was deeply investigated. 對碳纖維蜂窩夾層結構的動力學問題進行了深入分析。
- If any sample weld is deficient, all welds shall be checked. 若任一取樣焊縫有缺陷，需檢查所有焊縫。
- A three-dimensional finite element model was used to analyze buckling in honeycomb sandwich laminated structures with cutouts and reinforcements. 該文針對含有開孔和孔邊補強的蜂窩夾芯復合材料層合結構的屈曲分析發展了一套三維有限元求解方案。
- A honeycomb sandwich panel inside and an aluminum cladding outside for the ideal combination of solidity and lightness,coldness and heat. 內有蜂窩夾心板，外包鋁質覆層，乃是堅固性與質地輕盈之完美結合，又使冷熱合為一體。
- ALL WELDS 1/4" CONT.FILLET U.N.O. 除非另有說明,所有焊接（圓角）為1/4"連續圓角
- It is indicated that method proposed in the thesis is feasible to solve the buckling problems of honeycomb sandwich plates with debonding. 這表明本文的方法 對于求解 含面芯脫膠蜂窩夾芯板的總體失穩問題是切實可行的。
- All weld build-up or buttering shall be 100 % examined by MT, followed by RT or UT. 所有補焊或對接焊應先進行100%25磁粉檢測，接著作100%25射線或超聲檢測。
- The mechanical properties of a kind of honeycomb sandwich structure under effects of low temperature,particle radiation,ultraviolet ray and hot cold cycles etc. 以選定的一種蜂窩夾層結構為例，對其低溫力學性能即拉伸、壓縮、剪切等進行了各種外界環境包括溫度、粒子輻照、紫外輻照、冷熱循環等影響前后的性能測試和研究。
- Through the theoretical analysis of the flexural properties of FRP honeycomb sandwich construction, it proves that the values of theory and test agree well. 本文對玻璃鋼蜂窩夾層結構板的彎曲試驗結果(四邊簡支和四邊固支)進行理論分析,理論值與試驗值符合得很好。
- In Talien New Port, the bridge which joins coast land to the off shore deep water oil tanker wharf is composed of nine spans of 100 metres all welded open web trusses. 在大連新港工程中，連接陸地和油碼頭的棧橋是由九跨百米、全焊的空腹桁架組成的。
- Review and update all welder certificates as required. 按要求審核并更新焊工證書。
- All welds or soldered structural joints should be inspected. 應該檢查所有焊接或被焊接的結構聯接。
- Thus it can be see that the compressive strength of steel honeycomb sandwich panels in-plane compression is primarily supported by faces and honeycomb cores only have sustentative and steady effects. 由此可見，鋼蜂窩夾芯板的面內壓縮抗壓強度主要由面板承受，蜂窩芯只起支撐穩定作用。
- The large-scale honeycomb structure, an important component of the last stage fuel tank of launch vehicles, is composed of the honeycomb sandwich and thin aluminum alloy sheets with ellipsoid shape. 大型蜂窩共底構件是液體運載火箭末級推進劑箱的一個關鍵部件，它是由蜂窩夾芯復合材料和上、下薄鋁合金蒙皮粘接固化而成的。
- The novel concept of average minimum moment of inertia (AMMI) is presented and the formula for obtaining AMMI of a cellar array for a thick honeycomb sandwich plate or beam is derived. 提出了平均最小橫截面慣性矩的概念，并推出了常用蜂窩夾芯板梁的平均最小橫截面慣性矩的計算公式，解決了厚蜂窩夾芯板梁胞元陣列慣性矩的計算問題。
