您要查找的是不是：
- gear reduction ratio 齒輪減速比
- steering gear reduction ratio 轉向齒輪機構降速比
- High reduction ratio during primary and secondary crushing stage. 初段,二段等各段破碎均有大破碎比。
- Using lumped mass model, we construct dynamic equation of the flexible arm as well as its Simulink model. Using Simulink model, we analyze how Coulomb friction, motor inertia and reduction ratio of gear affect system performance. 采用集中質量模型建立了柔性手臂的動力學方程及其Simulink模型,利用Simulink模型仿真分析了庫侖摩擦力、電機轉子慣量和齒輪減速比對系統性能的影響。
- The midheaven axis gear reduction electrically operated actuation,does not need to refuel the province space. 中空軸型齒輪減速電動驅動，無需加油省空間。
- Gear reduction system may consider to be pinion transmition in stead of planetary system to saving spacing . 為節省空間起見，降齒系統可以考慮采用小齒傳動，而不用星系系統。
- They will vary by catalog number and style, for example Nippon Denso Gear Reduction unit minimum measurement is 1.2mm (.047”). 它們會(huì )隨著星表數目和式樣的變化而變化。如NipponDenso齒輪縮小型部件的最小值是1.;2mm
- NIBCO electric actuators operate on the gear reduction motor principle, which allows opening and closing speeds ranging from two seconds to one minute or longer. 美國尼伯科電動執行機構采用齒輪減速電機原理，因此開啟和關閉速度控制在兩秒至一分多鐘范圍內。
- The inspiratory expiratory value difference (VD) and area reduction ratio (AR) of bilateral lungs were calculated. 結果各年齡組內男女之間的VD和AR無顯著性差異;
- Because there are different ways to build a gear reduction unit, eg chain and sprocket or gearbox, we are only showing you the setup angle of the muller. 由于有不同的方法來建立一個齒輪減速裝置，如鏈及鏈輪或變速箱，我們只顯示您的馬勒設置的角度。
- Through the comparison of numerical simulation value and experiment results, the range of reduction ratio was obtained while the tube forming ideality. 通過數值模擬與實驗結果的比較，得出了獲得較理想的成形薄壁筒形件時減薄率的選取范圍。
- It is found that the tensile strength and the hardness of the specimen decrease, while the elongation and the reduction ratio of area increase. 在平行試樣方向上施加強磁場進行退火處理后，球鐵的拉伸強度、硬度降低，延伸率、斷面收縮率升高。
- The uneven distribution of the reduction ratio of Mo square bar swaged into the circular bar and the Practice calculation method of reduction ratio were discussed. 討論了鉬方坯旋鍛歸圓前壓縮比的不均勻分布情況及其實際壓縮比的計算方法。
- The star cracks in macrostructure appear in some hypo-peritectic continuous cast alloy blooms and these cracks cannot be stock completely by hot rolling reduction ratio, macroetching testing and SEM. 摘要一些亞包晶合金鋼連鑄大方坯出現低倍星狀裂紋，在一定的壓縮比下經軋制仍不能完全消除這種低倍缺陷。
- Vertical type gear reduction motor 產品描述:立式減速馬達
- At last, new failure thickness reduction ratio criterion is used to determine the forming limit of St14 steel based on the numerical system, and the prediction are compared with experimental FLD. 最后，在數值模擬中應用不同形式和參數組合的厚度減薄率判據進行成形極限圖預測，并與實驗結果進行了比較。
- Horizontal type gear reduction motor 產品描述:臥式減速馬達
- The star cracks in macrostructure appear in some hypo-peritectic continuous cast alloy blooms and these cracks cannot be stuck completely by hot rolling reduction ratio,macroetching testing and SEM. 一些亞包晶合金鋼連鑄大方坯出現低倍星狀裂紋,在一定的壓縮比下經軋制仍不能完全消除這種低倍缺陷。
- The driven gear fits its driving gear like a glove. 這個從動齒輪與它的主動輪嚙合得非常好。
- My whole morning's work has been put out of gear by that mishap. 我一個上午的工作全讓這倒霉的事給弄得亂了套。
