您要查找的是不是：
- 邵爾A硬度Shore A hardness
- 將得到的氯丁橡膠/蒙脫石納米復合材料進行性能測試,結果表明:邵爾A硬度、拉伸強度、300%定伸應力、500%定伸應力等均得到提高,其中300%、500%定伸應力較普通橡膠增加一倍;Property of vulcanized CR/MMT nanocomposite weretested, the results indicated that, compared to pure CR, the nanocomposite exhibitedbetter higher hardness, tensile strength, 300%25 tensile stress at a given elongation and500%25 tensile stress at a given elongation, in which 300%25 tensile stress at a givenelongation and 500%25 tensile stress at a given elongation were enhanced one times.
- 隨著填充油粘重常數的增加 ,SBS的拉伸強度和邵爾A型硬度增加。The tensile strength and Shore A hardness increased with the increase of viscosity gravity constant.
- 硫化膠的邵爾A型硬度、拉伸強度、100%定伸應力、300%定伸應力及扯斷永久變形增大,阿克隆磨耗量減小;the vulcanizate presented higher Shore A hardness,tensile strength,modulus at 100%25,modulus at 300%25,and elongation at break,and lower Akron abrasion loss;
- 結果表明 :采用過氧化物硫化體系時 ,EPDM與 1,2 PBR和BR并用后 ,硫化膠的交聯密度、10 0%定伸應力、邵爾A型硬度和撕裂強度增大 ,且前者的增幅較大 ;The results showed that the crosslinking density,the modulus at 100%25 elongation,the Shore A hardness and the tear strength of EPDM/1,2 PBR and EPDM/BR cured with the peroxide curing system increased,and those of EPDM/1,2 PBR increased more significantly;
- 結果表明,與SBR相比,淀粉/SBR復合材料的焦燒時間縮短,硫化速度減慢,且隨著淀粉用量的增大,復合材料的ML和MH增大,邵爾A型硬度、300%定伸應力、拉伸強度和撕裂強度顯著增大;The results showed that in comparison to SBR,the starch/SBR composite gave shorter scorch time and lower curing rate,and as the starch loading increased,ML and MH of the composite increased,and its Shore A hardness,modulus at 300%25,tensile strength and tear strength increased significantly;
- A股市場A share market
- "那伐爾" 系統navigation and ranging
- Ｘ射線硬度X-ray hardness
- Ｋ蒙乃爾鎳基合金K Monel
- 表ATable A
- 可機加工硬度machinable hardness
- A亞群Subgroup A
- ＤＣＩ奧爾塞貯存環DCI Orsay storage ring
- 表面顯微硬度Surface microhardness
- 齊次A子模homogeneous A-submodule
- 塔爾油tall oil
- (A北朝D386-581)北朝鮮North Korea
- 塔爾癥狀Tar's symptom
- TFⅢATFⅢA
