您要查找的是不是：
- The wind load resistance is80 N/ m2 for maximum sizes, i. e.11 m/ s. 最大尺寸門的抗風壓能力為80牛頓/2，即11米/。
- Perform load rating for new or existing bridges in either AASHTO Standard (LFD) or LRFR specifications. 雙重代碼功能也適用于載荷評級鑒定。
- There appears some flexibility at the top of tower with high ratio of height to diameter (H/D),caused by wind load. 高徑比(H/D)較大的塔在風載荷的作用下,在塔頂處會(huì )引起一定的靜撓度。
- Shall we get down to the loading rate now if you do not mind? 如果您不介意的話，我們現在來談?wù)勓b船率如何?
- If a tarpaulin/ sheeting is secured to the scaffolding, has the scaffolding been designed to withstand the additional wind load? 如果腳手架上固定了帆布/皮，腳手架的設計能力能夠承受額外的風力負荷嗎?
- The effects of five adjusting parameters of valve timing, admission valve clearance, emission valve clearance, rotational speed ,load rate are interacted. 配氣相位、進氣門間隙、排氣門間隙、轉速、負荷五個調整參數之間是相互影響的。
- Wind loads are not a significant factor for structural design. 風載荷對于結構設計就成了沒有意義的因素。
- With greater axial and radial load rating capacity, good replaceability of components. The shaft can be adjusted through external hexogan then to adjust the axial part dimension. 軸承徑向和軸向的承載能力都比較大，各配件可替換性強。軸承通過調節偏心外六角來調整芯軸位置進而達到調整側滾輪軸向尺寸的目的。
- Firstly the pulse wind load was determined and time process curve simulation of the pulse wind load was done by AR method. 首先確定了點支式玻璃幕墻魚腹式柔性支承體系所承受的風荷載,運用AR法對脈動風荷載進行了模擬;
- This time the entire structure of the high-rise building wind load resistance all the strength and stiffness to achieve maximum efficiency. 這個時候此高層建筑的整個結構抵抗風荷載的所有強度和剛度將達到最大的效率。
- Duncan Chang hyperbolic model used widely in FEM analysis of the interaction between tools and soil was modified by taking account of the influence of load rate. 并利用所測的曲線對準靜態情況下被廣泛用于土壤與機具相互作用的有限元分析的Duncan－Chang雙曲線模型進行修正，得出了考慮加載速率影響的修正Duncan－Chang模型
- If a tarpaulin/sheeting is secured to the scaffolding, has the scaffolding been designed to withstand the additional wind load? 如果腳手架上固定了帆布/鐵皮，腳手架的設計能力能夠承受額外的風力負荷嗎？
- The fracture toughness was strongly affected by temperature and loading rate. 結果表明:溫度和加載速率都對斷裂韌度產生影響;
- Wind load is a crucial controlling factor for high-rise structure.So, after confirming its shape coefficients, we can begin to design it. 摘要風荷載是高聳結構的控制因素，對高聳結構必須先確定體型系數，才能進行設計。
- The basic load ratings provided in the product table take this into account. 根據產品表中列出的基本額定,這一點已被考慮到。
- Wind load is a main variable in OCS design, its right selection is very important for safety operation of OCS and economic efficiency of the system. 風荷載是接觸網設計中主要的可變荷載,風速取值的正確與否對接觸網的運行安全及系統的經濟性至關重要。
- Greater height needs increased column and beam sizes to make buildings more rigid so that under wind load they will not sway beyond an acceptable limit. 建筑物高度增加就要求增大柱和梁的尺寸，以加強建筑物的剛度，使其在風荷載下左右晃動保持在可接受的限度內。
- The writer introduced briefly the load rating practices of Gears published by AGMA of the U.S. A in 1958, admitting that they are an advance in gear design for seores of years in U.S. and may also be helpful to the designers in other nations. 作者簡單地介紹了美國AGMA1958年公布的齒輪承載能力設計計算方法,認為是幾十年來美國齒輪設計方法的進步,方法精神,有可取之處。
- The conclusion demonstrates that the pulsating wind load is a vary harmful for the structure of ACSR,and the suggested coefficient of wind vibration was given. 研究成果不僅驗證了脈動風荷載對這種結構是一種非常不利的荷載形式;而且給出了這種結構風振系數的建議取值.
- The wind was whispering in the trees. 一陣風穿過樹林沙沙作響。
