您要查找的是不是：
- Cylinder liner water inlet low pressure slow-down. 缸套水入口壓力低降速。
- A water inlet and outlet are located on the rear panel.A control tap with flexible hose is positioned near the platen so that the water can be directed to any part of the platen during the grinding. 在拋光盤上設有可彎曲軟管，出/入水管接駁口設置在儀器的背面，并附有水龍頭開關，可直接將水沖向樣品，能加強潤滑作用，對研磨工序十分有幫助。
- Install a shut-off valve in the cold water inlet line. 在冷水進水管處安裝一個關閉閥。
- Install a shutoff valve in the cold water inlet line. 在冷水進水管處安裝一個關閉閥。
- Install a vacuum relief anti-siphon device in the cold water inlet line. 在冷水進水管上安裝一個反虹吸的真空安全法。
- Turn off water supply at the shut off valve in the cold water inlet. 關閉冷水進水閥門來關閉水供應。
- Close the cold water inlet valve and open a nearby hot water faucet. 關閉冷水進水閥，打開附近的熱水水龍頭。
- The hot water outlet and cold water inlet are identified on the back panel of the heater. 這種類型熱水器的熱水出水口和冷水進水口位于熱水器的面板后部。
- The Urinal flush valve is able to be connected with top or rear water inlet urinal ceramics. 吉博力小便沖洗閥可與上進水或后進水的小便器相連。
- Disconnect water piping connections to the cold water inlet and the hot water outlet. Disengage the heater from the wall bracket. 在冷水和熱水接口處拆下水管。從墻支架上拆除熱水器。
- The discharge capacity of grate opening as rain water inlet directly affects the drainage capac-ity of the highway. 雨水口篦子泄水量是雨水口泄水能力好壞的關鍵因素 ,其設置的好壞直接影響道路路面排水效果。
- After soldering, flush piping and install valve using filter washer on hot and cold water inlet and fiber washer on the mixed water outlet. 焊接后，沖洗管道，隨后采用熱水和冷水進口處的過濾器墊圈和混合水出口處的纖維墊圈安裝閥門。
- The hydraulically-operated thermostat opens a spring loaded check in the cold water inlet allowing cold water to mix with the hot water. 水壓控制的溫度調節裝置在冷水進口處開啟彈簧加壓的止回閥，讓冷水進入與熱水混合。
- Water squirted (from the tap) all over me. (龍頭里的)水噴了我一身。
- If the drain hose does not have this rating, open the cold water inlet valve and open a nearby hot water faucet until water is no longer hot. 如果排水軟管的額定溫度沒有達到上述要求，請打開冷水進水閥，打開附近的熱水水龍頭，直到水不熱為止。
- Can all glass vacuum collector tube operate with water inletting? 全玻璃真空集熱管不能頂水運行嗎?
- Install a listed temperature-pressure relief valve in the opening on the side of the heater. Install a vacuum relief anti-siphon device in the cold water inlet line. 在熱水器側面的開口位置上安裝額定溫度/水壓的安全閥。在冷水進水管上安裝一個反虹吸的真空安全裝置。
- Water splashed into the bucket from the tap. 水從龍頭里噴濺著注入水桶中。
- If the valve fails to completely reset and continues to release water, immediately shut off the cold water inlet valve, and call a qualified service technician. 如果閥門無法完全重置，并繼續釋放水，則要立即關閉冷水進口閥門，打電話叫有資格認證的工程師。
- The hydropower station water inlet of Baise multi-purpose dam project is key project, but the side slope geology condition is bad and its structure is complex. 百色水利樞紐電站進水口邊坡地質條件差,結構復雜,是電站引水發電的關鍵工程。
