您要查找的是不是：
- Knowledge of General maintenance of twin screw extruder and mixers. 了解攪拌機和雙螺桿擠出機的基本維修。
- Two layouts of gear box in twin screw extruders are discussed. 文中介紹了雙螺桿擠出機齒輪傳動的兩種設計方案。
- The corotating twin screw extruders is applied widly on processing of polymer. 同向雙螺桿擠出機在聚合物的加工中得到了廣泛的應用。
- It is a very important behavior of twin screw extruders that the screws are only partially filled with extrudate when operating. 摘要雙螺桿擠壓機工作時，“螺桿僅部分充滿”是其一個非常重要的特性。
- Six twin screwed steel steam cruisers. 六條雙螺紋鋼蒸汽巡洋艦。
- A twin screws roller refiner without knife can realize fibers ex tr uding in their axis direction in the commercial scale. 利用無刀式磨漿設備(雙螺旋輥式磨漿機)制漿,在工業上實現了纖維軸向擠壓。
- A series of silane grafted polyethylenes were prepared by using the twin screw extruder. 以雙螺桿擠出機為反應器，制備了一系列硅烷接枝高密度聚乙烯。
- Distributive mixing is achieved in twin screw extruders with narrow kneding block segments. 而分布混合是將熔體分割為條紋，進行均化，增大接觸面積。
- A series silane grafted polyethylenes were prepared by using the twin screw extruder. 以雙螺桿擠出機為反應器，制備了一系列硅烷接枝聚乙烯。
- Reciprocating Kneading and Extruding System,Clamshell Barrel Co-rotating Twin screw Extruder,PET Washing Line. 往復式單螺桿混煉擠出機，剖分式同向平行雙螺桿混煉擠出機，PET瓶片清洗生產線.
- With a windowed twin screw extruder the authors conduct several visualization extrusion experiments. 在可視化雙螺桿擠出實驗的基礎上，闡述了熔融過程中物料運動的多樣性問題。
- By comparison, the TATSR has higher efficiency of pumping. plasticization and mixing than that of twin screw reactor. 與雙螺桿反應器相比，三螺桿反應器具有較強的物料輸送能力、塑化和混合能力；
- This production line adopts single or twin screw extruder as the customers actual production needs. 這條生產線采用單一或雙螺桿擠出機作為客戶實際生產的需要。
- The mixing facilities have experienced the following steps: Roll mixer,Banbury mixer,Single screw extruder,Twin screw extruder and Twin rotor continuous mixer. 混煉設備的發展經歷了下列幾個主要階段:開煉機、密煉機、單(雙)螺桿擠出機和雙轉子連續混煉機。
- Using the datum curves from the twin screw extrusion experiment,the correlative factors influencing the fill ratio of screw are analysed. 利用雙螺桿擠出實驗中的實驗數據曲線，對影響螺桿填充率的諸相關因素進行分析。
- The process of imported twin screw extruder as finishing equipment of adhesive chloroprene rubber(CR 244)was introduced. 介紹了用進口雙螺桿擠出機作為粘接型氯丁橡膠(CR244)后處理裝置的工藝流程,探討了其工藝條件及成品橡膠的性能。
- The composite of glass fiber reinforced PET (FRPET)/Ultra-fine CaCO3 modified by La3+ (UCa-CO3-La3 + ) was prepared by twin screw extrusion. 采用雙螺桿擠出制備了玻璃纖維增強PET(FRPET)/稀土鑭化合物改性超細碳酸鈣(UCaC03一La3’)復合材料,將UCaCO3-La3+對FRPET性能的影響與有機鈉鹽類成核劑NA做了對比。
- The difference between TPU twin screw continuous reactor and conveyer belt production method was indicated and analysized. 比較并分析了熱塑性聚氨酯彈性體(TPU)雙螺桿法與傳送帶法生產工藝之間的差別。
- Maleic anhydride(MAH) and styrene(St) melt-grafting onto polypropylene(PP) was conducted in haake torque rheometer and twin screw extruder. 在哈克流變儀和雙螺桿擠出機對苯乙烯(St)/馬來酸酐(MAH)/聚丙烯(PP)熔融接枝進行了研究。
- The melt grafting of itaconic acid (IA) onto low-density polyethylene (LDPE) was initiated by dicumyl peroxide (DCP) in a twin screw extruder. 以過氧化二異丙苯(DCP)為引發劑,在雙螺桿擠出機中制備了衣康酸(IA)熔融接枝低密度聚乙烯(LDPE)。
