您要查找的是不是：
- Verticality of track and wheel should more than 999/1000.The center distance of wheels is 5835mm and the relative difference of it is no more than 1mm. 輪對軌間的不垂直度不得大于1/1000,車輪順軌中心間距5835mm的相對差值不得大于1mm。
- The center distance of R/L crank between piston with cylinder concern the power of engine. 活塞與汽缸的間隙直接影響引擎運轉之特性，因此最佳的間隙值會(huì )使引擎產生最佳的馬力及燃燒的廢氣。
- Model : Defined by the center distance between shafts. The bigger the model number. The bigger the reducer structure. 型號:由減速機入力和出入之中心距而定，型號越大，減速機體積越大。
- Dies seat: Adopt West Germany technology (Inlay type), assure the drawing center distance to avoid the wire breakage. 模座：采用西德技術（鑲入式），保證拉伸的中心距，減少斷線機率。
- KT-series is as the same as ZT-series and its principle is adjusting the center distance of roller-sting to welding the weld material of different diameter. KT系列產品與ZT系列產品相同，工作原理是人工調正滾輪架的中心距，以適應不同直徑焊接體的焊接。
- When the center distance of two involute gears is fixed, the plane higher pair composed by them will introduce one restriction to the mechanism. 摘要當參與嚙合的兩個漸開線齒輪之間有固定的中心距時，其構成的平面高副引入一個約束；
- You must enable Message Tracking Center on each server for which you want to track messages. 必須在要跟蹤其郵件的每一臺服務器上啟用郵件跟蹤中心。
- The change of center distance due to non-conjugate of corrugating roller in molding corrugated board process was discussed. 摘要論述了瓦楞輥在成型瓦楞紙板過程中，由于瓦楞輥的齒形是非共軛齒廓，中心距是變動的。
- Ship hull's sagging and hogging may cause center distance increasing or reducing to longitudinally disposed gear housing. 船體中垂及中拱彎曲變形會(huì )使沿船體縱向布置的齒輪座中心距產生增減。
- The center distance of the roller on the cradle draft assemble greatly affects the yarn eveness, hairiness and ends breakage. 摘要牽伸裝置上羅拉的中心距及其定位對成紗的條干不勻率、毛羽、斷頭都有較大影響。
- For unknown class label samples set，an unsupervised feature selection algorithm based on center distance ratio principle is proposed. 針對未知類標號的樣本集，提出基于中心距離比值準則的無監督特征選擇算法。
- Calculates the coordinates of the spindle and drive shaft and checking the center distance, determined department spindle must use dislodges the gear. 計算主軸、傳動軸的坐標并進行中心距驗算，確定部分軸上需采用變位齒輪；
- In order to avoid the “midconvex” of tooth profile and the serious abrasion in dedendum, the technology of center distance variation was adopted. 為了避免出現齒面“中凸”及齒根部研磨較嚴重的現象，采用了變中心距研齒工藝。
- The product output to sprain torque ,which make gears the least load and (with the equal center distance)can inproue more 30% bearing capacity than the traditional load capacity. 本產品為輸出升扭，使各檔輪所受載荷減小，相同中心距較傳統結構提高承載能力30%25以上。
- Our pilotless rocket enters the track of the earth. 我們把一個無人駕駛的火箭送入了地球的軌道里。
- The article introduces the calculation equation of how the gauge sets up and calculates the roller center distance which is of guiding signification to cotton mills and cradle manufacturers. 文章介紹了搖架上羅拉隔距規設定隔距的計算公式的推導過程，對棉紡廠、搖架制造廠具有指導意義。
- This rough track will soon be a metalled road. 這條坑坑洼洼的路不久就要鋪上碎石了。
- I'm trying to track down my old Aunt Maud. 我正試圖尋找到我那年邁的嬸嬸莫德。
- The cyclist went at full sail along the track. 自行車手沿著跑道全速前進。
- Bill has a feeling he is on a fast track. 比爾感覺到他正快速邁向成功。
