您要查找的是不是：
- Fine grain size for the smaller contact area. 接觸面積小時用細的粒度。
- Hard grade for the smaller contact area. 接觸面積小時用硬的結合度。
- Soft grade for the larger contact area. 接觸面積大時用軟的結合度。
- Coarse grain size for the larger contact area. 接觸面積大時用粗的粒度。
- The contact area between clamp and terminal is either silver or copper. 夾頭和電極之間的接觸面是銀的或銅的。
- The tooth contact and kinematic precision of the modified worm gearing with manufacturing errors has been investigated by the TCA method. 用齒面接觸分析法求解了存在制造誤差時修形傳動的齒面接觸狀態和運動精度。
- A tooth contact analysis model with a rotating freedom was developed by coupling freedom method to determine the stress and strain field of gears. 摘要利用自由度耦合方法建立了縣有旋轉自由度的齒輪接觸模型，用以分析齒輪的應力應變場。
- Squat and minimize the contact area with the ground as far as possible. 應該蹲著并盡量減少與地面接觸的面積。
- The computational models for tooth contact analysis (TCA) and loaded tooth contact analysis (LTCA) of the face gears were established. 建立了直齒面齒輪副輪齒接觸分析(TCA)和承載接觸分析(LTCA)的計算模型。
- When paged, subjects completed a brief questionnaire containing rating scales of jaw pain, masticatory muscle tension, time and intensity of tooth contact, mood and stress level. 記錄時，參與者要完成一份簡短的問卷，包括下頜疼痛等級、咀嚼肌緊張度、牙齒接觸的時間和強度、情緒和壓力水平。
- On the basis of the first envelope ,the paper stresses on the tooth contact analysis of the second envelope,and the equations of a worm and a wormwheel flanks are derived . 本文在第一次包絡(luò )的基礎上，著重進行了二次包絡(luò )齒面接觸分析，推導出了蝸桿和蝸輪齒面方程。
- Slowly pull the assembly outward to open check allowing exposure of the seat and clapper contact area for cleaning. 慢慢將止回閥往外拉，打開止回閥，使得閥座和閥瓣接觸面暴露出來便于清洗。
- Check ring gear and pinion gear teeth contact pattern. 檢查環形齒輪齒接觸印痕。
- The new concepts of flatness, contact area rate, dot distribution and so on are defined. 本文中對適印織物定義了平滑度、接觸面積比、網點分配數等新概念 ;
- The contact area between the fluoroalkylsilane film and liquid is small with the effect of the-CF3 group. 并用接觸角測定儀三甲基氯硅烷和氫氟硅酸在不同摩爾配比下薄膜疏水性能。
- Based on the coordinate transformation method and gearing theory, the mathematical models for generating the rack cutter, pinion, face-gear, as well as Tooth Contact Analysis (TCA), are established. 應用座標轉換法與齒輪嚙合原理，本文已導出創(chuàng )成齒條齒面數學模式、小齒輪齒面數學模式、面齒輪齒面數學模式、齒面接觸分析數學模式及控制拋物線運動誤差大小之統御方程組。
- The deformation on the flexible structure of contact area presented in this paper was analyzed using FEM. 采用有限元法對本研究提出的柔性接觸結構進行接觸變形分析；
- To increase the contact area and permit larger loads to be carried, the balls run in curvilinear grooves in the rings. 為了增加接觸面積并承受較大載荷,滾珠在內外環的曲線槽內滾動。三、譯成疊詞形式。
- The flexible structure of contact area can reduce the relative slippage between the stator and the rotor effectively. 本研究提出的柔性接觸結構能有效減少定、轉子間的相對滑動。
- Whichever method is used, and finally the need to brake drum brake shoe and the contact area for more than 70%. 無論采用哪種方法，最后必須使制動鼓與制動蹄的接觸面積達到70%25以上。
