您要查找的是不是：
- There are static error and dynamic error in the measurement of thermocouple. 熱電偶的測溫存在靜態誤差和動態誤差。
- Examples of static error are the addition of a string to an integer and querying for a nonexistent node for typed data. 靜態錯誤的示例包括將字符串添加到整數,以及在不存在的節點中查詢類型化的數據。
- Methods of error compensation for azimuth holding system in an INS (inertial navigation system) are presented. 給出了陸用慣性導航系統方位保持儀的誤差補償方法.
- Simulation shows that the DMMC controller can respond to the input instructions quickly without static error. 仿真顯示，DMMC法實現了對輸入指令的零穩態誤差快速響應。
- An error compensation method for intelligent electromagnetic compass (IEMC) is studied. 研究了一種智能電子羅盤的誤差補償問題。
- Error compensation technology is efficiency track to improve rotary accuracy of precision machine tool. 誤差補償技術是提高精密機床主軸回轉精度的有效途徑。
- The meassure to reduce the static error when manufacturing axial parts on a hydralic profiling tool slide is deduced in theory with positive feedback adjusting method. 本文應用順饋校正的方法，從理論上導出了在車床上用液壓仿形刀架加工軸類零件減小穩態誤差的措施。
- Error compensation is an efficient way to improve machining accuracy of NC machine tools. 誤差補償技術是提高數控機床加工精度的有效途徑。
- Abstract: The meassure to reduce the static error when manufacturing axial parts on a hydralic profiling tool slide is deduced in theory with positive feedback adjusting method. 文摘:本文應用順饋校正的方法，從理論上導出了在車床上用液壓仿形刀架加工軸類零件減小穩態誤差的措施。
- To avoid the singularities from appearing after gross error compensation, necessary cycle detection is added. 通過加入必要的回路檢測，避免了幅度補償后矩陣奇異性的產生。
- Short-circuiting device, open a way implement use at error compensation with load. 短路器、開路器和負載用于誤差抵償。
- A survey on the error and error compensation technology (ECT) of machine tools is presented. 采用誤差補償技術是提高機床加工精度的一個重要發展趨勢。
- Based on PIGA's error models,The effect of inertia system fix error angle to instrument's static error models,dynamic error models and amalgamate error models were analyzed. 在已建立的陀螺加速度表誤差模型的基礎上,分析在慣性系統中安裝誤差角對儀表靜態誤差模型、動態誤差模型和混合誤差模型的影響。
- It possessed these merit: fast response speed、low adjustive quantity、better quality of constringency and little static error, etc.These merits have been proved through Matlab. 該算法綜合了模糊控制算法和PID控制算法各自的優點， MATLAB仿真試驗結果表明其具有響應速度快、超調量小、收斂時間短、靜態誤差小等優點。
- In the guidance radar network, system error compensation is the predominate condition for information sharing and data fusion and is a key technique. 在制導雷達網中進行精確系統誤差補償是實現制導雷達組網信息資源共享與數據融合的先決條件,是實現制導雷達組網的關鍵技術之一。
- And a novel method via initial determined error compensation is presented in order to reduce the influence of shop motion and lever-arm effect. 并提出了采用初始裝定誤差補償的方法消除船舶運動與桿臂效應對射擊的影響。
- Analysis of field statics error in seismic exploration. 地震勘探野外靜校正量誤差分析
- The method enables the IEMC to realize automatic error compensation and auto-calibration easily,and lower the cost largely. 該方法使智能電子羅盤容易地實現了自動誤差補償和自動校準 ,大幅度降低了成本。
- After having analysed on error separation technique theory, the author begins to research on error compensation technique succeedingly. 經過對誤差分離技術理論進行了分析之后,又對誤差補償技術進行了研究,并建立了多點法測量形狀誤差的補償控制系統。
- Then the controller for VCM is designed using an integral-enhanced composite nonlinear feedback (CNF) control technology, which is capable of fast and smooth set-point tracking without static error. 音圈電機的控制采用一種積分增強的組合非線性反饋(CNF)控制技術,實現快速和平穩的設定點跟蹤,消除擾動因素可能造成的靜態誤差;
