您要查找的是不是：
- On Updating Rubber Plate Expansion Joints on Inner Ring Rd, Shanghai 上海內環高架路橡膠板伸縮縫改建
- Selection of Reconstruction Options for Rubber Plate Expansion Joints of Bridges and Highways 橋梁、公路橡膠板伸縮縫改建方案選配
- Counter flange with duct of exhaust expansion joint shall be supplied by MHI. 帶排汽膨脹節導管的配對法蘭由MHI提供。？
- Seal materials for furnace expansion joints. 窯爐砌體膨脹縫密封材料。
- The causes of the failure of austenitic bellow expansion joint in the operating FCC unit are comprehensively analyzed. 對在役催化裂化裝置的奧氏體不銹鋼波紋管膨脹節失效原因進行了全面分析 ,由于剛度、溫度、安裝等因素引起的膨脹節失穩以及Cl-和SO2 引起的腐蝕破壞 ,是膨脹節失效的主要破壞形式。
- This expansion joint installed on the side of pipeline to convenience the device installing, dismounting and repairing. 本伸縮節安裝于閥門等設備管路的一側，便于設備的安裝拆卸以及維修。
- All splicing plates, tubing clamps and miscellaneous hardware shall be Type 316 stainless steel. 所有拼接板、管夾和其它硬件應為316不銹鋼材質。
- Making Investigations on Early Damage of TST Expansion Joints. 道路伸縮縫TST伸縮縫早期破損探討。
- Air intake and air outlet of motors use metal hose expansion joint; Entrance and exit of pump use rubber flexible connectors. 風機進出風接口處均設金屬伸縮軟管柔性接頭；水泵進出口均設橡膠軟接頭。
- Expansion joints of various kinds are fitted on gas mains. 各種各樣的伸縮接頭被安裝在煤氣的總管道上了。
- Expansion joints of various kinds are fitted on steam pipes. 各種各樣的伸縮接頭被安裝在蒸氣管道上了。
- The result showed that slipping of faying surfaces occurred earlier when using thinner splice plates, and the plastic buckling deformation was also greater. 結果表明：采用較薄的拼接板時，試件的拼接區滑移出現得早，拼接板的塑性屈曲變形也變大；
- Expansion joints of linings of vari-ous types of heating equipment. 各種熱工設備砌體的膨脹縫；
- This paper introduces the construction technique of longitudinal expansion joint of EMR epoxy resin in Huanghe Bridge on Yingu expressway. 本文介紹銀古三標黃河特大橋EMR脂化合物縱向伸縮縫的施工技術。
- Based on the criteria of the expansion joint for the deckhouse of ship, its application in the deckhouse of medium-speed craft is reviewed. 根據國內各艦船規范對艦船甲板室設置伸縮接頭的有關規定,回顧并揭示了早期艦船甲板室設置伸縮接頭的原因及后來在中速艇上的使用情況。
- Measures for adopting bellows expansion joint have been proposed to meet the requirement of allowable force in the inlet of pump pipeline. 為滿足泵管口的受力要求,提出了采用波紋管補償器時應采取的措施。
- These buildings usually have no or less expansion joint, which leads to the length of whole structure oversteps the value our country Coad prescribed. 由于考慮到建筑上的美觀性和結構上的整體性,這些建筑往往不設或少設溫度伸縮縫,致使通長不設縫的結構長度遠遠超出了我國規范規定的伸縮縫限值。
- The key factors affecting the stagnation point position of L-type pipeline section are the setting position of bellows type expansion joint and the bend angle degree. 影響水平轉角管段駐點位置的主要因素為波紋管補償器設置位置、彎頭角度。
- The different expansion joint set in lining-up BOF will lead the different of contact pressure between lining and shell,and further produce different thermal-stress. 轉爐爐襯砌筑時設置的膨脹間隙不同會(huì )導致?tīng)t襯與爐殼之間的接觸壓力不同,進而導致?tīng)t襯的熱應力不同。
- He only put a bit on his plate to make fashion. 他只是撥了一點食物到盤子里做做樣子。
