您要查找的是不是：
- The results showed that the cool time, iron temperature, bind temperature and bonded fabrics had influences on the heat shrinkage rate of wool fabric. 結果顯示，熨燙冷卻后的放置時間、熨燙溫度、熨燙黏合溫度及黏合襯的種類均會(huì )影響到毛織物的熱縮率。
- The result shows that volume and coverage shrinkage rate of persimmon in sphere cylinder are smaller than in sphere.Drying persimmon in... 計算結果表明,干制后形狀呈球臺體較球體的體積收縮率和表面積收縮率均小,有利于表觀質量的提高。
- In addition, it had little influence on the compatibility with superplasticizer, and could reduce the shrinkage rate of mortar, had no dangerous on steel corrosion. 爐渣對水泥的外加劑相容性影響不大，能降低水泥膠砂的干縮率，不會(huì )對鋼筋銹蝕造成危害；
- He joined the two pieces of wood together with glue. 他用膠水將這兩塊木料黏在一起。
- He shored up the wall with a thick balk of wood. 他用一根粗大的木頭把墻撐住。
- That lathe is used for shaping pieces of wood. 那個車床是用來加工木材的。
- From MA content in polymer, drawing temperature and medium, after- chawing process and heat setting temperature, the factors affecting the shrinkage rate of PAN fiber are analyzed. 著重從聚合物中丙烯酸甲酯的含量、熱拉伸介質和溫度、后拉伸工藝以及熱定型溫度出發,分析各因素對纖維收縮率的影響,探討它們與腈綸收縮率之間的內在聯系。
- Don't let the fire go out; there's plenty of wood. 不要讓火滅了，有的是木柴。
- Keep that piece of wood; it may come in useful. 留著那塊木頭，它可能會(huì )有用的。
- Surgical and radical resection rates were 94.4% and 85.3% respectively. The shrinkage rate of tumor mass was 79% after pre operative TAC based on CT imaging changes. 本組手術切除率為 94 .;4%25;根治性切除率為 85
- The hut was made out of pieces of wood. 這小屋是用木板建造的。
- The two pieces of wood were wired together. 這兩塊木頭已用金屬絲捆在一起了。
- The man cleft a block of wood in two with an axe. 那人用斧頭把一塊木頭劈成兩半。
- The changes of the shrinkage rates of polyester fabrics in fusible interlining in different temperatures and times are discussed. 取三種粘合襯與滌綸面料粘合,測試不同的粘合溫度和放置時間條件下縮率的變化,并且進一步分析了這一變化。
- Oak is a good type of wood for making furniture. 橡木是制作家具的好材料。
- Using average shrinkage rates of injection-molded parts to decide the dimension of mold cavity can not satisfy the demand of high precision injection-molded parts. 采用一般的平均收縮率方法來確定模具型腔的成型尺寸，已難以滿足精密注塑成型制品的精度要求。
- Clamp these two pieces of wood together. 把兩根木頭鉗緊。
- What's the going rate of computer programmers? 計算機程序設計人員的一般工資是多少？
- One quality of wood is that it can burn. 木料的一個特點是能燃燒。
- The ground was littered with chips of wood. 地上到處都是木屑。
