您要查找的是不是：
- Complete detail drawings of the screw thread insert (Part 2#) by the assembly drawing of the jack. 根據千斤頂裝配圖拆畫件2螺套的零件圖。
- Contents: understand the assembly drawing of a jack and complete detail drawings of a screw thread insert by the assembly drawing. 內容：讀懂千斤頂裝配圖，并由裝配圖拆畫件2螺套的零件圖。
- Using F type screw thread connection. 采用F型螺紋連接方式。
- While displacement is usually driven by a texture, the Screw Thread shader uses an expression instead. 當置換是通常用一個紋理來驅動，螺紋材質使用一個表達式替代。
- Specification is 3/4-3 ins. Inlet and outlet is screw thread joint. Used for Pulse-dust-cleaning system. 規格有3/4-3英寸，進出口為螺紋連接，最適用于脈沖清灰系統上。
- Screw thread gauge is the most extensive and practical detector in thread machining. 螺紋量規是螺紋加工中應用最廣泛、最實用的檢測工具。
- The connection between the screw thread stread structure and inlay circle ensures the airtight of the whole lamp. 采用螺紋結構與鑲圈連接的方式保證了燈具整體的密封性能。
- Taper screw thread for valve stem and cylinder neck assembly.Nominal diameter 16,4, taper 3/20, 14 TPI si. 氣瓶.;氣瓶閥門頸裝配錐螺紋
- A toothed rack was commonly adopted for the automatic screw thread rotational unloading. 自動旋轉脫螺紋一般采用齒輪齒條機構或液壓齒輪機構。
- The connection between the screw thread structure and inlay circle ensures the airtight of the whole lamp. 采用螺紋結構與鑲圈連接的方式保證了燈具整體的密封性能。
- During the design of injection mould for screw thread accessory, the key problem is the demolding of screw thread. 在螺紋零件注塑模設計中,螺紋脫模是模具設計的關鍵。
- The threaded holes in the front suspension cradle, if damaged, can repaired by installing a Heli-Coil® thread insert. 前懸吊架的螺紋孔如有受損，可裝上Heli-Coil®螺紋套座加以修理。
- The Screw Thread shading network is a good example of how displacement can be driven by a mathematical expression rather than a conventional texture map. 螺紋材質網絡(luò )是一個好例子，它證明了如何通過一個數學表達式來驅動置換，它強于一個方便的紋理貼圖。
- Lubricate adjuster screw threads and pivot with spray lube. 使用噴霧潤滑油潤滑調整器螺絲螺紋和樞軸。
- If a threaded hole in the suspension cradle needs to be repaired, only use the type of thread insert and installation procedure specified for this application. 如果懸吊架有螺紋孔需要修復，僅限使用專用的螺紋套座以及特別安裝程序。
- A steel tool for cutting or finishing screw threads. 螺紋梳刀雕刻或精加工螺紋的鋼制工具
- Type of "T".valves: Specification is 3/4-3 ins. Inlet and oulet is screw thread joint. Used for Pulse-dust-cleaning system. 型閥：規格有3/4-3英寸，進出口為螺紋連接，最適用于脈沖清灰系統上。
- Compared the current samples with the standard sample from DIN912, the different point is the screw thread are more longness than standard sample. 當前的樣品和標準樣品DIN912相比;不同之處是螺紋的長度大于標準樣品.
- Used in the stands of [refinish rolling or in the front stands of common mills and roll rings for hot rolling screw thread steel. 用于予精軋機架或一般軋機前部機架以及熱軋螺紋鋼輥環。
- The other components of the case such as the rotating bezel also require a hand finish, particularly for drilling the screw thread and polishing. 表殼的其它部件，如旋轉表圈等，同樣須用人手處理,特別是鉆螺絲內牙和拋光。
