您要查找的是不是：
- Wuxi Turbine Blade Works Co., Ltd. 無錫透平葉片有限公司。
- KEY WORDS Anisotropic, Constitutive model, Viscoplastic, Turbine blade. 關鍵詞：正交異性，本構模型，粘塑性，渦輪葉片
- The wall thickness of the hollow aeroengine turbine blade is a critical parameter for ensuring its strength. 航空發動機空心渦輪葉片的壁厚是保證葉片強度的一個關鍵參數。
- Check no damage for fan blades and turbine blades. 檢查風扇葉片和渦輪葉片無損壞跡象。
- An example of rabbet feature manufacturability of a turbine blade was given to show the method available. 最后以渦輪葉片榫頭特征的可制造性分析為應用實例，說明該方法的有效性和實用性。
- Check no damage for fan blades and turbine blades . 檢查風扇葉片和渦輪葉片無損壞跡象。
- This paper presents the scheme of a versatile robot for on-site repair of hydraulic turbine blade. 介紹了一種多功能的水輪機葉片坑內修復機器人方案和研究進展。
- The RE-aluminizing technique and coating structure of gas turbine blade made of alloy M38G are studied. 研究了渦輪葉片材料M38G合金滲稀土-鋁涂層的工藝過程和組織結構。
- Turbine blade inspection poses some unique challenges, such as analyzing the twist of a newly manufactured blade compared to the CAD model. 對渦輪葉片檢驗面臨一些獨特的挑戰,如分析新制造出的葉片相對于CAD模型的扭曲程度。
- In this paper, heat transfer and fluid flow in passage for trailing edge of turbine blade with pin-fin arrays is studied numerically. 本文應用湍流模型對渦輪葉片尾緣針肋通道的換熱與流動進行了二維數值模擬研究。
- Utilizing frictional damping to carrying out vibration reduction on the steam turbine blade is a kind of simple and effective method. 利用摩擦阻尼對汽輪機葉片進行減振是一種簡單而又行之有效的方法。
- Because of huge deformation of turbine blade in the process of forging, the defects, such as folds and cracks, appear in blade forgings. 摘要在葉片鍛造過程中，由于變形量大，鍛出的葉片會(huì )出現如褶皺、裂紋這樣的缺陷。
- This steam is used to turn turbine blades of electric generators. 這蒸汽被用來推動發電機的渦輪葉片。
- Sophisticate cooling techniques must be employed to ensure that the turbine blade metal temperature is kept at an allowable level. 為保障工作葉片安全可靠的工作，必須采取有效的冷卻措施。
- This paper researches and develops an automatic polishing method to polish the turbine blade by the use of the Parallel Kinematics Machine Tool. 首先，對汽輪機葉片的拋光現狀進行了調查研究，了解到目前汽輪機葉片的拋光加工仍采用手工拋光的方法。
- The aerodynamic performance of the aft-loaded and fore-loaded turbine blade was investigated using the linear and annular turbine cascades experiments. 摘要采用平面葉柵和環形葉柵吹風試驗對后加載和高負荷前加載葉型的氣動性能進行了詳細的測量和研究。
- Full-Scale Structural Testing of Wind Turbine Blades TS Ed. 風力發電機組葉片滿量程試驗。
- Measurements of heat transfer and pressure drop in the short pin fin array used in trail cooling channel of turbine blade have been performed. 采用放大的模型對裝有五排短擾流柱的渦輪葉片尾緣的冷卻通道的流阻特性及通道端壁表面上的局部換熱系數進行了測量,重點研究了擾流柱直徑及形狀的影響。
- This paper analyses the formative reason,describes the methods of calculation and evaluation of erosion fatalness about steam turbine blade. 末級長葉片的水蝕是汽輪機正常運行過程中的常見現象。
- Finally, gave an example of rabbet-feature manufacturability of a turbine blade to show the method available and practicable. 最后以渦輪葉片榫頭特征的可制造性分析為應用實例，說明了該方法的有效性和實用性。
