您要查找的是不是：
- Replace the cylinder outlet seal and valve cap. 替換鋼瓶排氣口密封和閥門帽。
- Repeat steps2-5 until proper sag is achieved, then replace the air valve cap. 重復2－步驟以達到最佳預壓行程后，蓋上氣閥嘴帽。
- Repeat steps 2-5 until proper sag is achieved, then replace the air valve cap. 重復2－5步驟以達到最佳預壓行程后，蓋上氣閥嘴帽。
- Locate the Schrader air valve on the shock and remove the air valve cap. 找到避震上的美嘴氣閥，取下氣閥帽。
- ADS 34 adsorbent, newly developed by UOP, improved rotary valve and advanced ACCS system have been adopted in the unit. 該裝置采用UOP新開發的ADS 3 4吸附劑 ,改進的回轉閥及先進的ACCS控制系統 ;
- This valve is used with the rotary valve to control the material discharged from the bottom of storehouse. 流量控制閥用作控制庫底卸出的物料量，通常與氣動開關閥一起使用。
- Rotary valve is the key component of G-M type cryocooler which controls the intake and exhaust processes. 摘要旋轉閥是G-M型低溫制冷機的核心部件，用以控制制冷機進排氣時序。
- Unscrew the Allen screw in the middle of valve cap and lift up the cap just enough to pick up the old diaphragm. 旋松閥帽中間的內六角螺絲，并且提起閥帽，正好足夠拿走舊閥膜。
- All parts inside adopt the stainless steel, and are installed on the valve cap, maintenance is convenient. 內部零件全部采用不銹鋼制造，并且安裝在閥蓋上，維修保養極為方便。
- The rotary valve horn was invented in the early 19th century, and soon solved the problem of frequent changes of crooks in performance. 但于19世紀初,由于活塞的發明,解決了在演奏時需要經常轉換變音管的問題。
- Do not overheat cylinders to increase pressure or discharge rate. NEVER insert an object (e.g., wrench, screwdriver, pry bar, etc.) into valve cap openings. 禁止使鋼瓶過熱來增加壓力或流速。禁止把物體（如扳手、螺絲起子、撬桿等）插入閥門帽地開口處。
- Based on the analysis of rotary valve feeding apparatus of defibrator,a design method about double rotary valve feeding device was obtained. 在分析現有熱磨機回轉閥進料裝置的基礎上，提出了雙作用回轉閥進料裝置的設計思路。
- NEVER insert an object (e.g., wrench, screwdriver, pry bar, etc.) into valve cap openings. Doing so may damage the valve causing it to leak. 禁止把物體（如扳手、螺絲起子、撬桿等）插入閥門帽的開口處。這樣做可能損傷閥門，導致泄漏。
- The rotary valve is used to be switch in material flow control system, which is equipped with electric flow control valve tandem. 氣動開關閥主要在物料流量控制系統中作開關用，通常與電動流量控制閥串聯配套使用。
- NEVER insert an object (e. G., Wrench, screwdriver, pry bar, etc.) Into valve cap openings. Doing so may damage the valve causing it to leak. 禁止把物體(如扳手、螺絲起子、撬桿等)插入閥門帽的開口處。這樣做可能損傷閥門,導致泄漏。
- Based on the common contrl principle, It is designed that a commom rotary valve controls multiple cylinders by only one group of control hole. 應用公用控制理論，設計出只有一組控制油孔控制多個油缸的公用轉閥，此轉閥體積小、工作可靠、加工容易。
- NEVER insert an object (e.g., wrench, screwdriver, pry bar, etc.) into valve cap openings. Doing so may damage the valve causing it to leak . 禁止把物體（如扳手、螺絲起子、撬桿等）插入閥門帽的開口處。這樣做可能損傷閥門，導致泄漏。
- Imported all kind of valve oil, rotary valve oil, slide oil and cream, tube cream, key oil, fingerboard oil, and cleaning kit for all woodwind and brasswind instruments. 各種進口號油：小號活塞油，圓號活塞油，長號滑管油，銅管樂(lè )器調音管油，銅管樂(lè )器傳動軸潤滑油，木管樂(lè )器鍵油，提琴指板油，及各種樂(lè )器清潔套裝。
- The dynamic characteristic of rotary valve of hydraulic power steering gear was analysed, and the non-dimensional equation of loading pressure, loading flow was established. 摘要對液壓動力轉向器的轉向控制閥進行動力學分析，并且建立了負載壓力、負載流量的無因次方程。
- Principle and structure features of an on-off rotary valve type high frequency pulsating fluid signal generating device driven by D. C. motor are described. 介紹了一種由直流電機驅動的開關轉閥式高頻脈動流體信號發生裝置的原理、結構特點,以及將它應用于非定常流量測量實驗系統中的實驗結果。
