您要查找的是不是：
- The raised material should be smoothed away before the commencement of the wear test. 在磨損試驗開始之前應將隆起的材料弄平。
- The roll wear model for 1700 hot strip mill (HSM) was studied and the influencing factors on roll wear were analyzed. 以國內某1700熱連軋機為對象，研究了軋輥磨損模型，分析了影響軋輥磨損的各種因素。
- I guess some factories would just like to give you specially made samples for wear test, right? 我想有些工廠會(huì )特別做試穿樣品出對嗎?
- CVC(continuously variable crown) roll wear model for 1700 hot strip mill was researched and the factors affecting roll wear were analyzed. 研究了國內某廠1700熱連軋機CVC軋輥磨損模型,分析了影響軋輥磨損的各種因素。
- In order to carry out SFR, elimination or well-distribution of work roll wear and creation of special shape control technologies are necessary. 為了實現自由規程軋制需減少磨損量、均勻化磨損分布或開發特殊的板形控制技術。
- The simulation test of heavy rail straightening has been completed on M200 wear test machine. 在M200磨損試驗機上對重型鋼軌的矯直過程進行了模擬試驗。
- The paper covers introductions of ordinary rubber wear test methods and the standards for selecting test conditions. 介紹最常用的橡膠磨耗試驗方法和選擇試驗條件的標準。
- Aimed at the usual malfunctions of work roll,the countermeasures of reducing roll wear out are discussed from the roll manufacture and maintenance. 并針對工作輥易出現的故障,從軋輥制造和軋輥使用維護方面,探討了降低輥耗的對策。
- The materials were produced by P/M route and wear test was carried out in a MM-1000 type machine. 采用不同的燒結溫度,通過粉末冶金的方法制備了銅基粉末冶金摩擦材料,在MM-1000型摩擦試驗機上進行了模擬制動實驗。
- Aerial craft brake movable piece produced with new heat treatment process have basically met the special requirements of wear test. 運用該工藝生產的航空剎車副動片基本滿足了磨損試驗的特殊要求。
- The effect of load on tribological behavior of NBR and its mechanism were studied using an pin - on - disk friction and wear test apparatus. 采用栓-盤式摩擦磨損試驗機考察了載荷對丁腈橡膠摩擦學特性的影響,分析了其作用機理。
- Standard Test Method for Ranking Resistance of Plastics to Sliding Wear in Block-on-Ring Wear Test (Cumulative Wear Method) Using Micro-Tribometer mod. 標準試驗方法排行抗性塑料滑動磨損塊上環磨損試驗（累積磨損法）利用微摩擦國防部。
- Standard Test Method for Ranking Resistance of Materials to Sliding Wear in Block-on-Ring Wear Test Using Micro-Tribometer mod. 標準試驗方法排行電阻材料的滑動磨損塊上環磨損試驗用微摩擦國防部。
- Western armour looks like to be ponderous, but after experiment, they can run, jump and roll wearing it. 西方的盔甲看來笨重,但做過實驗,他們穿著後可跑跳,和做滾翻的。
- Three kinds of methods used now by china for vulcanite wear test were introdueed brief, and their merit and defect were also compared. 簡要介紹目前國內采用的硫化橡膠3種磨耗試驗方法，并將其優劣加以對比。
- Result of abrasive wear test showed that wear resistance of metallurgical coating was better than that of quenched 45# steel. 實驗結果表明，冶金層耐磨性比淬火45號鋼有較大提高。
- The wear test of Ni based alloy-Cr/WC composite coating without lubrication is carried on a MM-200 pin-on disc wear tester and study wear-resisting property. 在MM-200型銷盤式磨擦磨損實驗機上,對Ni基Cr/WC復合涂層進行了無潤滑的干磨擦磨損試驗,研究其磨損特性。
- By means of pin-on-disc wear test and reciprocating wear test, the effect of transfer layers on wear resistance of lubricating coatings, such as GLC coating, can be studied . 球盤磨損和往復磨損的主要特點是其測試GLC等減摩鍍層時，可以考察摩擦配副上轉移膜的作用；
- STUDY ON ROLL WEAR ON HOT STRIP ROLLING MILL 熱帶鋼軋機軋輥磨損研究
- Furthermore, regulations of the stress anddeformation of the exhaust valve in intensify wear test were discussedbased on I-deas finite element analysis program. 探討了氣門在強化模擬磨損工況下的應力及形變規律。
