您要查找的是不是：
- Application of Fuzzy Neural Network on Rolling Speed Control 基于模糊神經網絡(luò )駝峰溜放速度的控制
- In many speed control systems, e.g., rolling mills, mine winders, etc. 在許多速度控制系統中;例如軋鋼機;礦井提升機等負載要求頻繁地停機和反向運轉.
- The influence of rolling speed is not distinct. 軋制速度對界面結合的影響不明顯。
- The drill has variable speed control. 這鉆機有變速控制。
- Design of Speed Control System for Full. 實車碰撞車速控制系統的設計。
- Three stages wind speed control. 三段風速控制。
- Speed control systems will be built into cars. 汽車中將裝有速度控制系統。
- At a low steel rolling speed, the traditional AGC feedback control is not very good due to a long time delay caused by the thickness measurement. 在低速軋鋼時,由于測厚儀測量值的長時間滯后,傳統的后饋控制效果不好。
- LRP "Ai" digital speed control, installed. LRP的“愛”數字速度控制，安裝。
- The use of motor speed control, automatic cycloid. 采用可調速電機，自動擺線。
- Select the Rolling Speed at the pull down menu, then hold down the left click on the [ Rolling Up ] or [ Rolling Down ] to control the destination blind. 于下拉選單選好攪動速度后，用滑鼠左鍵按下[上移]或[下移]控制地點牌。
- It is pointed out that like the barrel type piercer process,the control of the cone type piercer roll speed is also very important. 指出了錐形輥穿孔機也要和桶形輥穿孔機一樣,要重視對穿孔機軋輥轉速的控制。
- The automatic current control and speed control of decoiler in pickling and cold rolling line are introduced. 介紹了配洗連軋線開卷機的自動電流控制和自動速度控制模式。
- The speed control strategy of mills and tabs in rough rolling section and APC strategy are given. 將磁致位移傳感器成功地應用到軋制生產中,提高了輥縫測量精度;
- Speed control switch input above the maximum acceptable voltage. 速度控制開關輸入高于最大可接受電壓。
- Install throttle cable, vehicle speed control cable (if equipped). 安裝節氣鋼纜、車速控制鋼纜（如果裝備）。
- The splitting rolling technology was applied to reso lve the problems of slow rolling speed, low productivity, etc. 針對嘉良鋼鐵公司棒材半連續式水平連軋機組軋制速度慢、產量低等問題,采用了切分軋制技術;
- Speed Control of Induction Motor Based on Passivity Theory P. 基于無源性理論的異步電機的轉速控制。
- While the rolling speed exceeds 2 m/s, the variation of heat drop gradually tends to become gentle. 制訂軋制規程時，出爐溫度可選擇合理范圍內的較低值以降低能源損耗；
- Conveyor speed can be configured to speed or speed control mode. 輸送機的速度可配置成定速或可調速的控制方式。
