您要查找的是不是：
- Ready for roller type &presser foot. 備圓輪式與平押式押腳兩種。
- Type GC-D is a roller type freewheel non-bearing supported, Earrings are required to support axial and radial loads. GC-D系列為無軸承支撐滾柱式單向離合器。
- Represents an array type with a component type that is parameterized or a type variable. 用已被參數化的組件類型或類型變量表示的數組類。
- Configuration variable included type variable, property variable, port variable and cardinality variable. 配置變量分為類型變量、屬性變量、接口變量、基數變量四種類型；
- Description: Type GC-A is a roller type freewheel non-bearing supported.Nominal outside diameter is a standard ball bearing dimension. 系列為無軸承支撐滾柱式單向離合器，外部尺寸與標準軸承尺寸相同。
- Or a reference type variable might not hold a reference to any object, in which case it is said to be a null reference or a reference to Nothing. 或者,引用類型變量可能不存放對任何對象的引用,這種情況稱為空引用。
- In this case, when the shorter length is converted to a longer data type variable, the bits in the upper 8 bits may not be set to the expected value. 這種情況下,當長度較短的變量轉換為較長的數據類型變量時,上8位中的位將不能設置為期望的值。
- The interval of oil changing of Variable drive is working 300h for the first time, then change oil every other 1000h, oiling to middle part of oil immersion lens from oil hole, never excess. 無級變速器首次換油時間為工作300小時，以后每隔1000小時換油，由注油孔加油至油鏡中部，切勿過量。
- It is indicated by test that the effect of step type variable parameter vibratile drilling is more superior than that of common drilling at corresponding conditions. 實驗得出，階躍式變參數振動鉆削效果明顯優于相應條件下的普通鉆削。
- Common interface for entities that have type variables. 有類型變量的實體的通用接口。
- It points out that the principle of hacking is low speed, centrifugal force is the key for separating, and roller type comber should be adopted, which causes little damage to apocynum fiber. 指出開松的原則是“低速度、慢開松、小密度”；分離的關鍵是離心力的大小，必須考慮終末速度和騰空速度；梳理成形則應采用完全羅拉式梳理，對麻纖維損傷小。
- The laminated material is an advanced compound material.A new vibratile drilling technology with step type variable parameter is suitable to process the new laminated material. 疊層材料是一種先進的復合材料，階躍式變參數振動鉆削新工藝最適合于加工新型疊層材料。
- It points out that the principle of hacking is low speed,centrifugal force is the key for separating,and roller type comber should be adopted,which causes little damage to apocynum fiber. 指出開松的原則是“低速度、慢開松、小密度”;分離的關鍵是離心力的大小,必須考慮終末速度和騰空速度;梳理成形則應采用完全羅拉式梳理,對麻纖維損傷小。
- Rotameter is a kind of traditional float type variable area flow meter with the advantages of stabilization, low pressure loss and the ability of measuring the low flow rate. 浮子流量傳感器是一種傳統的變截面流量傳感器,它具有工作可靠、壓力損失小和可測微小流量的特點,因此被廣泛應用于化工、石油、冶金、輕工、食品等流程工業中。
- Description: Type GC-C is a roller type freewheel non-bearing supported.Nominal outer diameter is the same as a series 62 ball bearings.Bearings are required to support axial and radial loads. 產品說明： 型號 GC-C 特性及應用: GC-C系列為無軸承支撐滾柱式單向離合器，外形尺寸與62系列標準軸承相同。
- This paper tentatively analyzes the realization mechanism of a reference type variable in C,and compares reference and pointer so as to deepen the comprehension of reference. 為準確理解C語言引用的本質,對C語言引用型變理的實現機制進行了初步探討。
- As a general rule, if a type is generic and you don't know or don't care about the value of the type variable, you should always use a ? wildcard instead of using a raw type. 作為泛化規則，如果一個類型是泛化的并且你不知道或是不關心泛型變量的值，你總是應該用?通配符替換一個原始類型。
- The Liebherr EC-HM is a new top-slewing crane series featuring continuously variable drives in all cases and exhibiting a high degree of modularity. 利勃海爾EC-HM是一個新型上回轉系列,在各種情況下均能夠連續可變傳動,并且表現出良好的模塊化性能。
- Based on analysis of problems existed in application of inertial vibrosieve,the new type variable frequency hydraulic straight-vibrating sieve is introduced. 分析了慣性振動篩存在的問題,提出新型變頻液壓直線振動篩的應用,并詳細介紹了液壓激振的理論成果。
