您要查找的是不是：
- Electronic speed controller to achieve optional rotation speed. 電子調速器任意調整轉速。
- Conclusions Rod rotation and in situ rod bending technique can satisfactorily restore the normal sagittal profile and regain vertebral height. 結論在使用撐開力恢復椎體高度的同時，應用旋棒原理可滿意地重建脊柱的正常矢狀面形態；
- Closed-loop control of rotation speed of4 WD electric vehicle is studied. 研究了4wd電動汽車的轉速閉環控制。
- Large deformation only occurs in the case of very high rotation speed. 只有在轉速極高時，彈道簧才會(huì )產生局部嚴重變形。
- The higher the rotation speed of the turnplate and the degree of superheat,... 轉盤轉速越高,金屬熔體過熱度越大,活化粉體粒徑越細。
- The principle of its technology transfer through the rod rotation torque by rotating the rotor at the stator the well fluid give rise to the ground. 其工藝原理就是通過抽油桿傳遞旋轉扭矩，靠轉子在定子內旋轉，把井液舉升到地面。
- Special lateral cross-flow fan makes lower fan rotation speed, which ensures lower noise and vibration levels. 獨特的交錯紋風扇設計有效減低轉速以降低噪音及震動。
- Allied Calliope rotation speed decreased to 33 from 35. Acceleration decreased to 1.3. Max speed decreased to 5 from 5.2. 管風琴旋轉速度從35降低為33。加速性降低為1.;3。最高速度從5
- Designed system can control the rotation speed of pneumatic motor effectively and thus get the adjustable feeding speed of the thread. 實驗表明:該控制系統可有效控制氣動馬達轉速,得到可調節的喂絲速度。
- Relation of quantity of fuel injection and needle vavle lift,rotation speed and pressure is got. 測定噴油量與針閥升程、噴油時間、主軸轉速、噴油壓力的關系。 (3)噴油量計算公式中修正系數K的確定。
- Amplified by proximity, the gravity of the stars modifies the rotation speed of the ellipses. 星球的重力被其近鄰的星球放大，進而修改了橢圓的旋轉速率。
- The higher the rotation speed of the turnplate and the degree of superheat, the more finer the particle size. 轉盤轉速越高，金屬熔體過熱度越大，活化粉體粒徑越細。
- With the circuit, the wheel rotation speed can be accurately measured even at low speed (<3km/h). 在較低車速下(<3km/h)仍能準確地測量車速。
- System adopt infrared photosensor measure motor rotation speed and drawing locus by black curve on the palette. 而對于不確定的曲線，由光電傳感器得到路線信息，經過單片機的處理，給出物體運動方向的指令。
- At first, the influence of load and rotation speed on mate-rial removal are investigated in this study. 本研究首先探討利用純鎳鍍層進行研光加工時，荷重與轉速對材料移除量之影響。
- Halving drill pressure and doubling rotation speed can not reduce the performance load between friction pairs. 軸承系統的徑向間隙越小，相應的峰值接觸壓力越低；
- Note: There are many choices becomes the rotational speed. 注:均質機轉速有多種選擇。
- In this paper,the effect of matching of rotation speed and travel speed on 6063 aluminum FSW joints is researched. 在此以工藝試驗為基礎,研究了旋轉速度及其與焊接速度的匹配對6063鋁合金攪拌摩擦焊接頭形貌以及力學性能的影響。
- Rotation speed is one of the key reasons which are relative to the quality of friction stir welds ... 攪拌工具旋轉速度是影響接頭成型形貌的關鍵原因之一,速度過低有可能會(huì )導致隧道型孔洞缺陷。
