您要查找的是不是：
- Study on Reverse Bend Test of Contact Wire of Railway Overhead Catenary Based on Foreign Standards 從國際國外標準談電氣化鐵路接觸線反復彎曲試驗
- Reverse bend test of metal 金屬反復彎曲試驗
- reverse bend test 反復彎曲試驗
- reversed bend test 彎曲試驗
- The structure,cold bending fraction pattern and EXD of Q235 plate cold bending test sample of Shanghai Meishan Company are analyzed. 對梅山公司Q235冷彎不合格試樣進行了金相組織、冷彎斷口形貌及能譜分析。
- The flexural strength of all FRC posts was tested with a 3-point bending test. 三點撓曲實驗比較不同彎曲度的FRC彎釘與FRC直釘的撓曲強度和撓曲模量。
- Application: Road profile rotating bending test on wheel hubs with simulation of wheel load and lateral forces. 應用范圍：公路概況與旋轉彎曲載荷和車輪的側向力輪轂模擬試驗。
- Furthmore, EFPI and FBG sensors embedded inside FOSL are performed by using the four-point bending test. 在此基礎上，對FOSL試件中的EFPI和FBG傳感器進行了四點彎曲試驗。
- A bend test is a simple test for ductility that does not require special equipment, or a specially shaped test-piece. 彎曲試驗是測試韌性的簡單試驗，不要求特別的測試設備，或規定形狀的試樣。
- Metal material bending test is an important item when raw materials come to factory in boiler and pressure vessel manufacturing trade. 金屬材料的彎曲試驗是鍋爐壓力容器制造行業進行原材料入廠檢驗的一項主要檢查項目。
- In this article tensile test,bending test and microhardness test were conducted on the laser welded joint of the steel sheet for automobile use. 對汽車用薄板的激光焊接接頭進行了拉伸試驗、彎曲試驗及顯微硬度分析等。
- reverse bending of hands and feet 倍拳
- In this test, air-dry woods of China-fir, Taiwan acacia, Lauan and Hemlock were used to monitor AB counts under static bending test. 本試驗以杉木、相思樹、柳桉及鐵杉之氣乾材為試材，測定靜力彎曲試驗時AE發生之情況，探討AE發生次數與應力、應變之關系。
- Moreover, Equation (5.15) predicts ovalisation at maximum bending strain while measurements were performed after the bending test. 此外，等式(5.;15)預測了在撓度測試后度量的基于最大彎曲應變的成橢圓形，
- The method to determine the interlaminar shear strength for composite material is also proposed by five-point bending test, and the experimen... 同時，文中提出了用五點彎曲實驗測試層間剪切強度的方法，給出了實驗結果。
- The adhesive force between the coating and the magnesium substrate has been estimated by using bend test,file test,and scribe test. 采用彎曲法、銼刀實驗法和劃線劃格實驗3種鍍層結合力測試方法;對化學鍍鎳層與鎂合金基體之間結合力的優劣進行了定性評價.
- The mechanical and failure characteristics of SFHPC beams in bending test can be described well by using fracture energy and flexural toughness indices together. 綜合利用斷裂能和彎曲韌性指標，才能更全面地描述混凝土在彎曲過程中的受力與破壞特征。
- On purpose to study bend properties of amorphous thin ribbons, a bend test method is given and a laboratory equipment has been established. 為研究非晶薄帶的彎曲特性,本文給出了非晶薄帶彎曲試驗方法,并且建立了實驗設備。
- By using elasto-plastic finite element calculation and three point bending test,the in-fluence of strength matching and crack depth on fracture properties are investigated. 利用彈塑性有限元計算和三點彎曲試驗對不同裂紋深度、不同強度組配焊接接頭試樣的斷裂性能進行了研究。
- Our army suffered a slight reverse. 我們的部隊受到輕微的挫敗。
