您要查找的是不是：
- The other host of signal are control signals. 另一組信號是控制信號。
- The response of a terminal to remote control signals. 終端對遠程控制信號的響應。參閱handshaking。
- Expands the control signal for parallel steam generators. 使用并聯的蒸汽爐時可用此配件擴大控制訊號。
- serial receive control signal 串行接收控制信號
- A control signal. 一個控制信號。
- Result The amplitude of ERP P180 and LPC, which can reflect mental fatigue,decreased after receiving control test. 結果反映大腦疲勞的事件相關電位指標LPC和P180在假性治療后波幅明顯減低,而真性治療后則波幅不降低。
- Injector #2 output driver does not respond properly to the control signal. 噴嘴%232輸出驅動器未對控制訊號作出正炒應。
- Injector #output driver does not respond properly to the control signal. 噴油器%237輸出驅動器沒有正確地響應控制信號。
- Design Of Programme - controlled Signal. 程控信號發生器的設計。
- For checking the evaluation device a control signal can be generated. 通過產生一個控制信號來檢查核定設備。
- The main control cell adopt LPC936 singlechip, which offers the control signal. 其主控制單元采用LPC936單片機，提供控制信號。
- Table 3-25 is a truth table of the 8251 bus control signals. 表3-25是8251總線控制信號的真值表。
- A logic element designed to act as either an adder or a subtracter in accordance with the control signal applied to it. 根據供給它的控制信號,或起加法器作用或起減法器作用的一種邏輯元件。
- It carries the micro-processor control signal or "interface signals". 它用以傳遞微處理機的控制信號（或稱“接口信號”）。
- A New Method Of Self-Learning and Revivification of Infrared Remote control Signal Based On Single Chip Microcomputer. 基于單片機的紅外遙控信號自學習及還原新方法。
- Using this information from the oxygen sensor and other inputs, the ECM generates a control signal to the carburetor. 根據氧傳感器傳遞過來的信息及其它輸入信號，ECM向化油器發出控制信號。
- Call Accepted Signal A control signal transmitted by the called equipment to indicate that it accepts an incoming call. 呼叫接受的信號被叫設備發出的控制信號,表明正在接收入局呼叫。
- The different control signal makes LBD to give out light with the pattern in different way. 不同的控制信號使發光二極管以不同的方式和花樣顯示。
- A continuous input pulse train triggers the monostable circuit, and a control signal modulates the threshold voltage. 持續不斷的脈沖輸入，導致單穩態的電路產生, 同時控制信號調整門限電壓。
- In order to gate out the required control signals, pins have to be multiplexed. 為了給出所需要的控制信號，管腿必須采用多路轉換。
