您要查找的是不是：
- Nothing seems to be wrong with the propeller shaft. 轉動軸看來沒毛病。
- Reindex propeller shaft 180° and evaluate. 將傳動軸翻轉180°，并測試。
- Remove the rear propeller shaft. 拆卸后傳動軸。
- Aligning intermediate shaft and propeller shaft after launching. 下水后中間軸和螺旋槳連接后校中。
- This measurement will give you the propeller shaft angle (C). 測量結果就是傳動軸工作角（c）。
- Measuring clearance between propeller shaft &bearing. 螺旋槳軸與軸承間隙測量。
- Different nacelle with deeper ross-section and intake over propeller shaft. 發動機艙、螺旋槳軸處的進氣口有一些不同。
- Install the straps and bolts to hold the propeller shaft to the yoke. 安裝扣夾和螺栓，將傳動軸固定到軸軛上。
- Align previously made marks on yoke and propeller shaft and install propeller shaft. 將定位軛架上的預制標記對準傳動軸并安裝傳動軸。
- Mark the propeller shaft and pinion yoke, or pinion flange, for installation reference. 在傳動軸和傳動軸軸軛、或小齒輪軸軛上作標記，作安裝的參考標志。
- Align the installation reference marks on the propeller shaft and yoke and install the propeller shaft. 對準傳動軸和軛上安裝參考標記，安裝傳遞軸。
- The reason the propeller shaft shortens as the angle increases is that the rear axle and differential move in a shorter arc than the propeller shaft. 當角度增加時,傳動軸變短的原因是后橋和差速器運動的弧度小于傳動軸運動的弧度。
- This accommodates any effective change of length of the propeller shaft as the rear axles move toward or away from the car frame. 當后橋在車架上向前或向上運動時,這種結構足以調整傳動軸長度的任何變化。
- The D9B can be equipped with a power take-off designed for propeller shaft operation or direct-mounted hydraulic pumps. D9B可提供適用于驅動軸運轉或直接安裝式液壓泵的動力輸出。
- The propeller shaft to be turned clockwise viewed from afterward of M/E when running ahead. 當主機正車時，從主機后面看螺旋槳軸為順時針旋轉。
- "The propeller shaft may be solid or hollow, protected by an outer tube or exposed. 傳動軸可以是實心的或空心的,由套管加以保護或裸露在外。
- "The propeller shaft is a drive shaft to carry the power from the transmission to the rear-wheel axles. 傳動軸是將動力從變速器傳送到后橋的驅動軸上。
- The results show that it is successful to adopt the technolngy of cold drawing with core mandrel for processing the propeller shaft tube s... 試驗結果表明,采用短芯棒冷拔工藝加工傳動軸管,在技術上是成功的。
- A propeller shaft that has been in use for a long period of time cannot be adjusteIf the length of the propeller is incorrect and causing vibration, replace the propeller shaft. 已經使用很長時間的傳動軸不能調整。如果傳動軸的長度不正確并引起振動，更換傳動軸。
- A careless driver is a menace to all road users. 漫不經心的駕駛員對于路上所有車輛和行人都是危險的。
