您要查找的是不是：
- Design of Multistage Power Amplifier in Ku Band. Ku波段多級功率放大器的研制。
- Purpose: Medium power amplifier applications. 用途:用于中功率放大。
- Purpose: Audio frequency power amplifier applications. 用途:用于音頻功率放大。
- Connect the Power Amplifier to Analog Channel B of the interface. 將功率放大器連接到接口上的模擬通道B。
- Purpose: Strobo flash, medium power amplifier applications. 用途:用于閃光驅動,中功率放大電路。
- In the end, it introduced a new type class-d power amplifier DPPC. 本論文所完成的開關功放已完成樣機試驗。
- Purpose: Power amplifier applications, vertical output applications. 用途:用于功率放大和幀頻輸出。
- The power of the modulated carrier wave is increased by the RF power amplifier. 射頻功率放大器增加了調變載波的功率。
- Purpose: Strobe flash applications, general power amplifier applications. 用途:用于閃光燈閃光驅動,一般功率放大。
- Purpose:Low frequency power amplifier,medium speed switching applications . 用途:用于低頻功率放大及中速開關。
- I'll demonstrate how to use the power amplifiers? 我來示范一下如何使用這個功率的放大器。
- Actuation of one clutch provides positive torque to the final drive, the capstan acting as the main power amplifier. 一個離合器的作用是給最后一級傳動機構，即作為主功率放大器的絞盤，提供正向力矩。
- Wide-band is the main trends of development of power amplifier, which is key component of broadband RF front end. 摘要功率放大器是射頻前端中的關鍵部件，寬帶是目前功率放大器的主要發展趨勢。
- If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. 如果連接一選購的電源放大器而不使用內置放大器，將不發出嗶聲。
- The SD may potentially be applied in both a voltage amplifier stage and in a power amplifier stage. 潛在的應用都可能處在一個電壓放大器階段、一個功率放大器階段。
- The ideal power amplifier would be supplied pure DC power ONLY from the power supply. 理想的功放是純直流電源供應只是供電。
- This terminal is to output signals to external constant-voltage power amplifier. 輸出到外部定壓功放,用于大廳、走廊、室外等擴聲范圍較大的區域。
- The application of the EDA simulate software Multisim 2001 was applied in a power amplifier of electronic design. 以功率放大器電路設計為實際例子;研究了EDA工具軟件Multisim2001在電子設計中的應用 情況.
- Before the main source is turned on, the Load Button for the power amplifier must be set "OFF". 在主電源打開前,功率放大器負載按鈕必須為“關”。
- Because the system need a power amplifier, analyzed the theory and designing of PA in the paper also. 同時根據系統的功率控制,需要一個推動功放,文章也對功率放大器的原理和設計方法進行了分析和介紹。
