您要查找的是不是：
- Plastic Limit Load of Welding Piping Tees Under the Action of the In-Plane Bending Moment 面內彎矩下焊制管道三通的塑性極限載荷
- Plastic limit load for a defect-free welded piping tee under the in-plane bending moment 焊制三通在面內彎矩作用下的塑性極限載荷
- Out-of-Plane Bending Moment Analysis of the Plastic Limit for the Welded Piping Tee Containing Bottom Thinning Defects 底部減薄焊制三通的塑性極限面外彎矩分析
- PLASTIC LIMIT LOAD OF CIRCUMFERENTIALLY CRACKED PIPES UNDER AXIAL FORCE, INTERNAL PRESSURE AND ASYMMETRICAL BENDING MOMENT 含周向裂紋管道在非對稱彎矩組合載荷作用下塑性極限載荷分析
- PLASTIC LIMIT LOAD ANALYSIS OF CIRCUMFERENTIALLY CRACKED PIPES UNDER THE COMBINED LOADS OF TORQUE, AXIAL FORCE, INTERNAL PRESSURE AND UNSYMMETRICAL BENDING MOMENT 周向裂紋管道在含扭轉各種組合變形時的極限載荷分析
- Analysis and experiments on the plastic limit load of elbows under in-plane closing bending moments 平面閉合彎矩作用下彎管塑性極限載荷分析與試驗
- ultimate limit bending moment 極限彎矩
- The actual stress is not proportional to the bending moment. 實際上應力與彎矩不成正比。
- But the bending moment at the central hinge must vanish. 但在中間鉸處，彎矩必定為零。
- The induced bending moment may lead to destructibility of the pipeline. 彎矩的產生可能導致管線的破壞。
- An analysis method for the connections of prestressed concrete slab to interior column under shear and unbalanced moment is proposed in this paper by applying the plastic limit state theory. 本文采用塑性極限分析方法并利用節點的對稱性,建立了預應力混凝土板柱中節點在剪力和不平衡彎矩作用下抗沖切和抗彎的相關方程。
- Shear force is implicit in the development of bending moments. 桿中的剪力在彎矩的推導中是不明顯的。
- It is concluded that the filled soil is silt soil with high liquid limit and plastic limit, which has the low swelling property in natural state. 結果認為，此路基填土為高液限和塑限的淤泥質軟土，天然狀態下具有弱膨脹性。
- The comparison between the test data and Billington experiential formula and ASME code shows that the formula was more accurate to the limit value in the in plane bending moment, and was very suitable for engineering application. 通過試驗數據驗證和與基于A(yíng)SME規范及Billington的經驗公式比較表明 ,該公式對面內彎矩極限值有較高的估算精度 ,具有較大的工程應用價值。
- In this paper,a simple method on the plastic limit analysis of annular plates under linearly load has been given out. 本文結合環板在線性荷載作用下的塑性極限分析問題,給出一種簡便的計算方法,即奇異函數法。
- This increases both the rigid body rotation of the vehicle and the bending moment. 這既增加了飛行器的剛體轉動，也增加了彎矩。
- The load when the key layer breaking instantly and strength condition were obtained by the plastic limit analysis method structure. 應用結構塑性極限分析方法，得到了關鍵層在破斷瞬時的載荷并建立了強度條件。
- In the FEM simulation of the loading identification process, the bending moment maintains a constant amplitude, hut its direction is alterable. 在有限元仿真計算中，彎矩載荷的大小保持不變，但方向可調。
- The unique phenomena at any cross section of EULER compressive bar under the zero bending moment is analyzed. 從理論上分析了歐拉壓桿任意截面上彎矩為零的狀態下所出現的奇異現象。
- In the plastic limit analysis,the wrinkler's plate is smartly analyzed in yield-line theory to get the critical compression strength of the coal pillar. 在分析過程中,利用機動法對溫克爾地基板(彈簧支撐板)進行了塑性極限分析,得出了煤柱抗壓強度的臨界值。
