您要查找的是不是：
- pipe cutting and threading machine 切管和車絲機
- Side slit should be in clean finishing with 1cm width topstitching all around, side seam end thread must keep and insert into slit. 側叉要還口處理，車1cm寬面線，側骨尾端要保留線尾并包在叉內。
- The main defects are deformation and burrs of cutting surface in the square pipe end. 切口變形和毛刺是矩形管管端的主要缺陷。
- The company owns the advanced production equipments, including the CNC lathe, automatic lathe, the forging 、twist thread machine. 公司擁有先進的生產設備,包括CNC電腦車床,各種型號自動車床，鍛打?搓牙機組。
- The basic principle and the method of oil drill pipe end upsetting process were presented. 介紹了石油鉆桿端部鐓鍛加厚工藝基本原理及加厚方式。
- The structure characteristics of the plain-end chamfering machine for stell pipe ends are described. 介紹了鋼管端面平頭倒棱機的設備結構特點。
- Mark out the pipe end by using scriber to assuer the inserted length and to avoidthe pipe of disconnection. 使用畫線器在管端畫線作記號，以保證管子插入長度，避免造成脫管。
- Two design program methods on inside tapered thread (left- ha nd)of the normal drill -pipe joint . They are cutting thread (G32) and fixed cyc le of threading(G82). They completed cutting thread machine, they are new machi ne way and track. 介紹正規式鉆桿接頭 7 5 /8"左旋內錐螺紋的兩種程序編制方法,即切削螺紋(G32)和螺紋切削固定循環 (G82 )的程序編制,完成了對 7 5 /8"左旋內螺紋的一次性完整挑扣加工,探索出左旋內錐螺紋加工的一條新途徑和新方法。
- Please disconnect the pipe ends and flush it with water. 管路末端要拆下來并且用水把里面的垃圾沖干凈。
- The package of products: painting, oil coating, Anticorrosion &Insulation, beveled edges or plain end, the protection of pipe end, packaging. 包裝說明： 噴漆；涂油；防腐保溫；坡口或平口；管端保護；
- Keywords Chamfering Machine fop Pipe End; 管道平頭倒坡口機;
- Cut square of pipe end is a very important parameter for steel pipe visional inspection.The traditional measurement cannot meet the requirements of larde diameter steel pipe. 管端切斜是鋼管外觀尺寸檢查的一項比較重要指標,對大直徑鋼管而言傳統的測量方法已不能滿足要求。
- Threading machine for rear axle house flange 后橋殼法蘭攻絲
- Before installing, be sure pipe ends are reamed and threads are cut to size. 在安裝之前，確保管道末端已經進行鉸孔，攻螺紋，并且切割成所需的尺寸長度。
- Screw thread gauge is the most extensive and practical detector in thread machining. 螺紋量規是螺紋加工中應用最廣泛、最實用的檢測工具。
- Pipe ends must be cut square, using a wheel-type cutter or saw &miter box. 管道端口必須順直角垂直切割，可采用輪式切割機或鋸子與軸鋸箱。
- With PRD PEEM's both spherical and semi-spherical pipe ends are possible. 可以使用PRD球形和半球形的管道終端。
- A loose end, fringe, or tuft of thread. 碎屑松散的線的末端、毛邊或一束線
- The accident put an untimely end to the party. 意外事故使聚會(huì )匆匆結束了。
- The boys were itching for the lesson to end. 那些男孩子們渴望下課。
