您要查找的是不是：
- anchor pin lock nut 鎖銷防松螺母
- Disc is fastened securely to disc hanger with a lock nut and cotter pin. 通過一個鎖緊螺母和開口銷將閥瓣安全緊固在閥瓣支架上。
- Install adjuster nut and lock nut. 安裝調節器螺母和防松螺母。
- Lock handle securely by turning lock nut clockwise. 3、順時針?lè )较驍Q緊螺帽，可靠的鎖好把手。
- To Readjust- Loosen lock nut on the adjusting screw. 重新調節：松開調節螺絲上的鎖定螺母。
- To Readjust - Loosen lock nut on the adjusting screw. 重新調節：松開調節螺絲上的鎖定螺母。
- Revolving the lock nut 5 anti-clockwise to the suitable position. 逆時針?lè )较蛐D鎖緊螺母5;使其退到適當位置.
- KMTA lock nuts can be tightened using a pin wrench with a stud to engage one of the holes in the circumference. KMTA鎖緊螺母可使用銷式扳手固定,這種扳手帶一個爪手,可插入圓周上的孔中。
- If only one locating ring is required, it should be inserted on the same side as the lock nut. 如果只需一個定位環,此定位環應插入與鎖緊螺母相同的一側。
- The first product we developed and completed based on this theme was the Hard Lock nut. 我們以此為出發點,開始了研究開發,經過不斷實驗終于研究成功了Hard Lock螺母。
- Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening angle. 孔徑最大為100毫米的小型軸承可通過測量鎖定螺母的緊固角度正確安裝。
- To replace diaphragm; loosen lock nut (48) and remove lock washer (46), diaphragm plate (60) and diaphragm (20). 要更換隔膜，先松開鎖緊螺母(48)，并拆卸鎖緊墊圈(46)，隔膜板(60)和隔膜(20)。
- Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem. 松開和拆卸隔膜鎖緊螺母和鎖緊墊圈，從閥桿上往下壓閥盤和隔膜。
- Remove spring cage, spring and washer. Remove bottom plug. Grasp upper and lower stem lock nut with wrench and loosen. Clean or replace any damaged or worn parts. 拆卸彈簧籠，彈簧和墊圈。拆卸底部塞。用扳手抓住上部和下部閥桿鎖緊螺母并且松開。清洗或更換任何損壞或磨損部件。
- Remove the locking nut from the flow/conductivity/temp sensor. 移開流量/導電/溫度傳感器上的固定螺絲。
- Remove the locking nut from the flow / conductivity / temp sensor. 卸除流量/電導/溫度傳感器上的鎖緊螺帽。
- The feasibility of repetitive use of Fe-based shape memory alloy lock nut has been studied in order to lower the usage cost. 為了降低鐵基形狀記憶合金防松螺母的使用成本,探索了該新型螺母重復使用的可行性。
- Measuring the lock nut tightening angle is a proven method to determine the correct degree of interference in small to medium-sized bearings on tapered seatings (fig). 測量鎖定螺母的緊固角是經驗證的有效方法,可用來確定圓錐軸頸上中小型軸承的正確過盈度(圖17)。
- Balancing wrench in left hand with graduations visible with the marked arrow elementary scale up, unlock knurled handle by turning lock nut counter-clockwise. 1、平衡扳手的左手有可見的分度和按比例放大的箭頭標記，按逆時鐘方向滾動鎖緊螺帽，開啟有刻度的把手。
- Put transversely the lock nut into the annular notch of the hole saw connector( see Fig.2), install the lock nut together with the hole saw connector onto the spindle of the pipe driller, and then fasten it with a crescent spanner. 先將鎖緊螺母沿橫向卡入孔鋸接頭的環形槽中（2）再將鎖緊螺母連孔鋸接頭一同裝上鉆孔機主軸，用月牙扳手扳緊。
