您要查找的是不是:
- Injection pressure and holding pressure i. 注射壓力和保壓壓力。
- Injection pressure was 20 pis, 5 sec and power supply was 15kV constant. 自動氣壓進樣;20pis;5sec.
- Injection pressure of J-ELIII series is different from that of JSW's hydraulic machines. 注塑壓力與油壓系列不同。
- Maximum injection pressure and maximum holding pressure may be restricted due to molding condition. 有的情形下,最大注塑壓力,最大保壓壓力會(huì )因成成形條件不同而受到限制。
- Colon hydrotherapy equipment can sustain a regulated and safe injection pressure to permit cleaning water to reach th extremities of the colon. 大腸水療法設備能夠維持一個規范和安全注射壓力,讓水清洗,以達到末端結腸。
- Increased needle injection pressure was obsered as the olume of PMMA increases and as the distribution of PMMA is in close proximity to the cortical walls. 同時,使用的聚甲基丙烯酸甲酯黏合劑的體積的增加還可以增大融合椎體的強度。
- The pH of buffer was 6.2, and the run-voltage was 7kV. Pressure injection model was used and injection pressure was 2406.25 kPa xs. 運行電壓為7kV,采用壓力進樣方式,進樣壓力為2406.;25kPa×s。
- In the Common Rail accumulator injection system, the generation of the injection pressure is separate from the injection itself. 在共軌蓄壓噴射系統,新一代的噴射壓力是分開的,從注射本身。
- The calculating formula for the plastics backface shrink pitfall value of the strengthening rib was put forward at considering the processing conditions of injection pressur... 提出了在考慮注塑壓力、注射溫度、注射速率等工藝條件下,塑料件加強肋背面的縮陷值的計算公式,并找出通過模具尺寸設計進行補償的方法。
- The injection pressure and flow rate and the lengths of injection and falloff periods are the key factors to the succession of well test. 注入的壓力、排量以及注入和壓降段的時間是關系到試井成功與否的關鍵因素。
- Die inserts, together with the cores which form recesses, must endure the effects of temperature and injection pressure of the molten metal. 與形式隱藏,必須忍受溫度和熔融金屬的射入壓力的作用的核心一起死插入物。
- Compared with the formation water drive reservoir without water-sensitive damage,the injection pressure of water drive in the water-sensit. 影響木缽區塊延10油層驅油效率的主要因素是儲集巖的孔隙結構非均質性、水敏傷害、注水壓力及加壓方式。
- Research results show that with application of Mucell,the 10% raw material can be saved,the injection pressure is decreased by 36.7%,the clamp forc... 研究結果表明:采用微孔發泡注射成型工藝可以節省原材料10%25;注射壓力降低了36.;7%25;鎖模力降低了60
- The results showed that Sauter Mean Diameter (SMD) of biodiesel decreased, as the injection pressure increased and the orifice diameter diminished. 結果表明:隨著啟噴壓力的增加和噴孔直徑的減小,生物柴油索特平均直徑不斷減??;
- Aiming at the feature of filling tube and injection pressure, non-flowback acidizing was developed to ensure the implementation of miscible flooding. 技術應用將會(huì )有一定的借鑒和指導意義。
- Many mountaineers have reached that mountain peak. 許多登山家都登上過那座大山的頂峰。
- We have a precipitous climb to the peak. 我們向著陡峭山頂攀登。
- The process parameters of bladder-assisted RTM, such as the injection pressure, temperature, the bladder pressure, and the pressure-holding time were determined. 研究和確定了氣囊輔助RTM工藝條件,如注射壓力、注射溫度、充壓大小和保壓時間等。
- Due to high injection pressure of high concentration polymer solution,reducing injection pressure of high-concentration polymer solution with surfactant has been researched. 針對高濃度聚合物溶液注入壓力高的實際情況,開展了表面活性劑降低高濃度聚合物注入壓力的研究。
- Tourism is at its peak in August. 旅游業在八月份達到高峰。