您要查找的是不是：
- Martensite lath changes into fine tempered sorbite w. 材料經高溫回火得到細小回火索氏體,力學性能優良。
- Crack propagation from the flameout edge can be modeled by considering an edge crack in the martensite surface from flame cutting. 裂紋從燒割邊緣的擴展可模擬為一個從燒割處的馬氏體表面起始的邊裂紋。
- Special, highly alloyed welding wire for aluminium pressure molds. Martensit hardening. Good filing qualities. 這是一種特殊的合金焊絲,用于壓鋁模具的修補中,具有較高的焊接硬度和良好的堆焊性能。
- The proportion of austenite in the matrix of as-cast cast iron 290Cr26MoW increases but that of martensite decreases. 鑄態290Cr26MoW耐磨白口鑄鐵基體的奧氏體比例增加,馬氏體減少。
- As for small diameter workpiece, martensite distribution can be obtained by immediately quenching. 對于直徑較細的工件，軋后立即淬火幾乎可得到全部馬氏體。
- Matrix should be of martensite, because it can resist impact and has little deformation. 基體應是馬氏體，它能抵抗沖擊，變形小。
- Tmis paper deals with the ordering of Fe-1.83C(Wt%)martensite during aging at roomtemperature. 利用透射電鏡對Fe－1.;83C馬氏體室溫時效所產生的有序化進行了詳細的研究。
- The large coarsened martensite and grainy bainite are the internal causes of brittlement. 粗大的馬氏體和焊接過程產生的粒狀貝氏體是脆化的內在原因.
- The results show that the structure of the surfacing layer was martensite, carbides and residual austenite. 試驗結果表明：焊后的堆焊層組織為馬氏體+碳化物+殘余奧氏體。
- Some martensite like bainites such as crossed type and midrib type in the alloy were investigated. 觀察到交叉型、中脊型類馬氏體形貌貝氏體，發現貝氏體中脊中有大量層錯。
- The microstructure of the weld bonds is a combination of martensite, lower bainite and retained austenite. 焊接熔合區組織為馬氏體+下貝氏體+殘余奧氏體；
- In stead of HCP precipitates, martensite distributed uniformly throughout the FCC matrix. 論文主題為探討此高錳鋼于高溫熱處理后所產生的麻田散體相變化情形。
- Overheating can result in overtempered martensite (OTM) or untempered martensite (UTM) formations in the base metal. 過熱會(huì )造成在本體金屬中形成過回火馬氏體（OTM）或者欠回火馬氏體（UTM）。
- The results show that the nitric martensite after cryogenic treatment has better wear resistance. 結果表明,含氮馬氏體深冷處理后有更好的耐磨性能。
- Ti martensite can be obtained by oil quenching from 920,the morphology of martensite is lathlike or massive. 油淬后獲得馬氏體組織，馬氏體在電鏡下呈塊狀和條狀。
- The micro structure of deposited metal is composed of martensite,residual austnesite and carbide hard phase. 堆焊層組織為馬氏體+殘余奧氏體+碳化物硬質相。
- Austenitic type is non-magnetic or weak magnetic properties martensite or ferrite is magnetic. 奧氏體型是無磁或弱磁性，馬氏體或鐵素體是有磁性的。
- Microstructure of heat-affect zone (HAZ) is mainly lath martensite, bainite and residual austenite. 熱影響區(HAZ)組織主要為板條馬氏體、貝氏體和少量殘余奧氏體；
- The hard second phase, for example martensite, contributed to the superior fatigue strength and higher threshold value. 較硬的第二相，如馬氏體，貢獻了出眾的疲勞強度和較高的開始值。
- The result indicates that there was a great deal of lath martensite in the quenched structure. 顯微組織中存在大量板條馬氏體，組織亞結構中存在大量位錯和孿晶。
