您要查找的是不是：
- Company business scope: Research, develop and assembly filler caps, FLVV, roll valve, inlet check valve and related products, sale the products and provide the related services. 公司經營范圍:研究,開發,生產和組裝油箱蓋,燃油排放控制閥,加油控制閥和油氣泄漏探測器及其他相關產品,銷售本公司所生產的產品并提供相關服務。
- Piston cooling oil inlet low pressure slow-down. 活塞冷卻油入口壓力低降速。
- pump inlet check valve 泵進口止回閥
- Check valve guiding shall be plastic to plastic. 止回閥引導裝置應該是塑料對塑料。
- Remove check valve and valve seal from booster. 從倍力器上卸去逆止閥和閥門密封。
- Connect vacuum hose to booster check valve. 連接真空軟管到增壓器檢測閥。
- To test for tightness of second check Valve. 檢測第二止回閥的密封性。
- ANSI FLANGED SWING CHECK VALVE CLAS. 美標法蘭止回閥。
- Reassemble the Check valve modules. 重新組裝止回閥模塊。
- Tubing or connectors affixed to the inlet and outlet ports of the check valve support structure allow for external fluidic access. 我們過去的研究，以便更好地面對新世紀的到來。一些研究人員甚至說，當人類登陸火星在二十世紀，突然發現，我們正面臨只不過是人類過去。
- Dual fireproof oil reservoirs should be designed,and the oil inlet height should not be lower than that of the water outlet to siphon oil in and drain water off. 防火油池應進行雙池設計,兩池中進油口和出水口不應同高或進口低于出口,這樣才能形成虹吸排水貯油現象;
- Connect vacuum hose to booster check valve . 連接真空軟管到增壓器檢測閥。
- Purpose: To test check valve No. 1 for tightness. 目的:檢測止回閥1號的密封性。
- Sticky outlet check valve poppet. 1檢查過濾的進水管線。
- CAUTION: The check valve spring is in compression. 警告：止回閥彈簧處于壓縮狀態。
- ME FUEL OIL INLET L.P. 主機燃油進口壓低。
- Check valves must be installed with the inlet in the direction of arrow. 必須按照箭頭所指方向安裝止回閥的進口。
- Gear pump apart to check and found that the shell scratch gear alloy scrap the oil inlets. 拆開齒輪泵檢查，發現齒輪將殼體刮傷，合金碎屑把出油口堵塞。
- Remove the four screws holding the first check valve cover. 拆卸固定第一止回閥閥蓋的四個螺絲。
- A check valve may be required ahead of the backflow preventer. 此時在防回流閥前面可能需要安裝一個止回閥。
