您要查找的是不是：
- Results show that the measuring method with the conductivity electrode placed at the nozzle outlet can describe objectively the distribution of the tundish fluid flow. 結果表明，只有將電導電極置于水口出流部位的測定方法才能客觀地反映中間包內流體的流場分布情況。
- By introducing the concept of fluidization factor, the required velocity at nozzle outlet starting to fluidize particulate material under different structural factor was obtained. 通過引入流化程度因子概念，采用正交試驗得到了不同結構參數下物料流化所需的噴嘴出口氣流速度。
- Both outlet temperature and CC are proportional to coal slurry concentration and [O]/[C] ratio. 出口溫度和碳轉化率隨煤漿濃度和[O]/[C]原子比的增加而增高。
- Calibrate the mixed water outlet temperature by placing a thermometer in the mixed water stream. 在混合水流內放置溫度計，校準混合水出口的溫度。
- The effects of different nozzle outlet angle,immersion depth of SEN and casting speed on the flow field were ascertained and suitable nozzle structure for the mold was established. 研究了不同水口傾角、插入深度及拉速等參數條件對結晶器內流場的影響,得出了適用于寬規格結晶器合理的浸入式水口。
- This valve requires periodic inspection and verification of the outlet temperature by a licensed contractor. 這種閥門需要由得到許可的承包商進行定期檢查和確認出水口溫度。
- The effect of outlet temperature and pressure of the debenzolization partial condenser on the rough benzol qualiy and output is explained and analysed. 分析了脫苯分縮器出口溫度、壓力對粗苯質量、產量的影響。
- This study thus provides an effective technical approach to adjust the outlet temperature field and develop the combustor. 該研究為燃燒室出口溫度場的調試及燃燒室的研制提供了一條有效的技術途徑。
- Analysis was made on how concentration of pulverized coal, primary air, mill outlet temperature and pulverized coal fineness affected ion ignition. 分析了煤粉濃度、一次風速、二次風量、磨煤機出口溫度和煤粉細度等因素對其點火性能的影響；
- The paper introduces the measures,such as decreasing recycle ratio,shortening coke-forming time,and rasing outlet temperature of oven to improve the severity of delay-coking unit. 介紹了鎮海煉化延遲焦化裝置為提高苛刻度所采取的降低循環比、縮短生焦時間、提高加熱爐出口溫度等措施情況。
- Deflection angle of gas flow at nozzle outlet 噴嘴氣流偏轉角
- The fuel and the compressor's IGV control algorithms are presented for the normal load regulating by combining the load and the turbine's outlet temperature control. 本文將負荷控制與透平出口溫度控制相結合，提出了正常負荷調整時的燃料量和壓氣機入口導葉控制算法。
- The inlet and outlet temperature of the evaporator can reach the steady evaporating temperature in a short time and the superheated temperature can be maintained in a small range. 蒸發器入口和出口的溫度在開機很短時間內就能達到穩定的蒸發溫度，并能穩定在很小的過熱度范圍內。
- Washers shall be color coded at hose nozzle outlets and mounted inside the fume hood and controlled from the exterior with color-coded index handles. 水龍頭在噴嘴處用顏色標示，并安裝在通風柜內部。其控制開關在通風柜外面，用不同顏色標示把手。
- The computer programme worked out this way has been applied in the measurement of gas temperature at the outlet of a certain high heat-tolerance combustor, obtaining the outlet temperature field. 根據此方法編制的計算機程序已應用于某高熱容燃燒室出口燃氣溫度測量中，獲得了燃燒室出口溫度場。
- Inlet temperature, outlet temperature and drying air volume are displayed digitally. Condition setting dials and stage level control switch are located on the front panel for easy use. 入口、出口和干燥氣流量數字顯示,條件設定板、進程控制開關為方便使用被置于前板。
- A Variable Width Design of Nozzle Outlet in a Turbocharger Scroll 增壓器蝸殼噴嘴出口的變寬度設計思想和計算
- Method To appraise the design of LCG, the thermal ma nikin wearing LCG and heat insulation garment was put in the temperature cabin, then the inlet and outlet temperature of cooling liquid in the LCG were measured and the heat removed was calculated. 方法溫度艙內暖體假人著液冷服和隔熱服 ,在不同的溫度環境和不同的暖體假人代謝率條件下 ,改變服裝設計參數 ,以獲得液冷服在不同實驗條件下進口液溫、液體流率與液冷服散熱量及溫度比效率間的關系。 并測量冷卻液進出口溫度 ,計算液冷服的實際散熱量。
- The ideal super critical refrigeration cycle of CO 2 is analyzed. For a given outlet temperature of the cooler, there exists an optimum cooling pressure that maximizes the coefficient of performance(COP). 文中對理想的跨臨界CO2制冷循環，進行了理論分析和性能計算，揭示了該循環的一些特點：對于一定的冷卻器出口溫度，對應一個使系統性能系數最佳的冷卻壓力，而且系統性能系數最佳時的冷卻器出口溫度與冷卻壓力的對應關系，可以用一個簡單的代數式表示；
