您要查找的是不是：
- Single plane mean bore diameter deviation. 單一平面平均內徑偏差。
- Mean bore diameter: arithmetical mean of the largest and smallest single bore diameters in one plane. 平均內徑:同一平面上最大和最小內徑的算術平均值。
- Single plane mean outside diameter deviation. 單一平面平均外徑偏差。
- Bore diameter variation in a single radial plane. 單一徑向平面內徑變動量。
- The size identification for Y-bearing units is the bore diameter of the incorporated Y-bearing. Y-軸承單元的尺寸代號表示所含Y-軸承的內徑。
- The bore diameter and width of the IR inner rings are made to Normal tolerances in accordance with ISO 492:2002. 根據2002年的ISO 492標準,IR內圈的孔徑和寬度以普通級公差制造。
- The tested solenoid has a bore diameter of 400 mm, stored energy of 0.445 MJ and a peak field of about 5 T. 被試磁體內徑400mm、儲能0.;445MJ;峰值磁場約5T
- There are no many vessels whose bore diameter is small in the root, and no ray in the xylem. 根中導管數量少，孔徑小，次生木質部不含射線。
- The influence of throttle bore diameter and melt temperature in internal ladle on constituent distribution, marco-structure androckwell hardness of the casting was investigated. 研究了節流孔徑和內澆包熔體溫度兩個工藝參數對鑄件的成分分布、宏觀組織和洛氏硬度的影響。
- Vsing this tool to process small bore diameter chilled steel,not only has high process accuracy,stabilizes process quality,but also raises tools using lifetime. 采用此刀具加工小直徑淬火鋼內孔,不僅加工精度高、加工質量穩定,又能大大提高刀具的使用壽命。
- cladding surface diameter deviation 包層表面直徑偏差
- reference surface diameter deviation 基準面直徑偏移
- Bearings up to and including 300 mm bore diameter are produced to higher precision than the ISO Normal tolerances. 孔徑達(含)300mm的軸承的制造,使用比ISO正常公差更高的精確度。
- Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening angle. 孔徑最大為100毫米的小型軸承可通過測量鎖定螺母的緊固角度正確安裝。
- Using this model, the paper studies the affection of the change of the bore diameter in each feature section to the initial velocity of projectile, and the relationship between the initial velocity of projectile and the total change of the bore diameter. 并用該模型研究了各特征截面內徑改變量對彈丸初速改變量的影響,以及彈丸初速改變量與總內徑改變量間的關系。
- The attenuation coefficient of the dominant mode is less than 1 dB/m when the dielectric material is polyimide and the depth is 0.05 mm,which is far less than that of the same bore diameter metal circle waveguide for THz radiation. 得出其主模在THz頻段的衰減常數小于1 dB/m,該值遠小于相同內徑的金屬圓波導在這一頻段的衰減常數。
- A pulsed magnet with 10 mm in bore diameter and a pulsed duration of 10 ms is designed, which can generate the magnetic flux density of 60 T. The behavior simulation of this magnet supplied by different pulsed power modules is also presented. 本文對一個內徑為10mm、能產生60T場強、持續脈沖時間為10ms的強磁體的相關參數進行了設計計算,并對該強磁體在不同脈沖電源條件下的電特性行為進行了仿真。
- It is well known that a lot of words associated with derogatory meanings bear some traces of female characters. 語言歧視是其中一個重要的研究話題。
- After extensive analytical work, a significant conclusion can be arrived at that the finger seal assembled with aft cover plate of smaller bore diameter has better synthetical characteristics of low hysteresis and stiffness. 從綜合影響角度考慮 ,具有較小后遮流板內徑的指尖密封體現出更為優良的低遲滯和低剛度的綜合特性。
- The better bond performance is due to larger bore diameter of the porous oxide film, higher porosity density, i.e., the bond performance improves with the increase of contact surface area. 良好的膠合性能因多孔質型氧化皮膜孔徑較大、微孔密度較高，即接著面積增加，則膠合性能也隨之上升。
