您要查找的是不是：
- Its finite element model is established. 構造了其有限元模型。
- A static finite element model of an air spring was given. 摘要文中建立了空氣彈簧的靜態有限元模型。
- The finite element model of opening gap tantalum thin-walled tube is setup. 為了控制鉭薄壁管焊接成形的質量,進行鉭薄壁管開口間隙場計算模型的研究。
- Primary study on the construction of the finite element model of tooth and post-core. 牙齒與樁核三維有限元建模的初步探討。
- Study Design. In vivo study of a computed tomography (CT)-based nonlinear finite element model (FEM). 研究設計：基于CT的非線性有限元模型(FEM)的體內研究。
- The principles to construct finite element model for modal analysis of the cylinder block have been obtained. 通過研究，得出了建立內燃機機體的有限元模型的一些原則。
- This paper deals with the finite element model of DWX hydraulic prop in aid of Pro/MECHANICA. 本文用Pro/MECHANICA有限元分析軟件,建立了柱塞懸浮式液壓支柱的有限元模型。
- The finite element model of a small punch test specimen of 1Cr0.5Mo steel is established. 基于小沖孔蠕變試驗 ;建立 1Cr0 .;5Mo耐熱鋼小沖孔蠕變試樣的有限元模型。
- The finite element model of the front m ember of one passenger car is created with its CATIA model. 利用轎車前梁的CATIA模型建立其有限元模型。
- Results A three-dimensional finite element model of palatal implant anchorage is successfully constructed, meeting t... 結果建立了符合生物力學研究需要的腭部種植支抗的三維有限元模型。
- Thermal expansion deformation for resistanee spot welding of low-carbonsteel is simulated by an finite element model. 用有限元方法模擬了低碳鋼點焊過程的熱膨脹變形。
- The present finite element model is shown to be reasonable in predicting the ossicular mechanics of human ear. 研究結果表明本文建立的人耳三維有限元模型對研究聽骨鏈聲學力學特性是有效的。
- This paper presents the development of a three-dimensional finite element model of central maxillary incisor. 以上頜中切牙為解剖學基礎建立了三維有限元模型。
- Key words: lumbar spine, destabilized spine, interspinous instrumentation, biomechanics, finite element model. 關鍵詞：腰椎，腰椎不穩，椎間融合器，生物力學，有限元模型
- A finite element model of swaying tree was established to explore the kinetic mechanism of swaying tree in wind field. 摘要為了探索樹木在風場中搖曳的運動機理，建立了風中搖曳樹木的有限元模型。
- Results Dismountable 3 D finite element model of mandible with denture is established. 結果得到具有可拆卸性、多用途的下頜骨及下牙列的三維有限元模型。
- The finite element model of hydro-mechanical deep drawing is established based on the commercial software DYNAFORM-PC. 采用商用有限元軟件DYNAFORM-PC，建立了筒形件液壓-機械拉深過程數值模擬模型。
- The finite element models simulating normal, pre- and post-PFO were created. 再者，可產生模擬正常、病患的股骨近端截骨術術前及術后情形的有限元素模型。
- Objective：To build a three-dimensional finite element model of temporomandibular joint and the mandible. 目的：建立正常人下頜骨三維有限元模型，為以后的生物力學研究和分析奠定基礎。
- At three-dimension finite element model is established to simulate PTS process and obtain its characteristic. 利用有限元方法，建立合理的三維計算模型，模擬核壓力容器進出口水管附近的承壓熱沖擊的過程和特性。
