您要查找的是不是：
- The C x H 1- x film are prepared using low pressure plasma CVD with trans 2 butene. 以反式?2?丁烯為工作氣體，采用低壓等離子體化學氣相沉積法制備 Cx H1－ x薄膜。
- Titanium coatings have been deposited onto 317L stainless steel plate by low pressure plasma spray(LPPS)process. 采用低壓等離子噴涂工藝，在317L不銹鋼質接骨板上噴涂了鈦涂層，制備出鈦涂層的接骨板。
- Silicone intraocular lens (IOLs) were modified with carbon and titanium respectively by the technique of ion beam combined with low temperature and low pressure plasma. 采用低溫等離子體聯合離子束技術對硅凝膠人工晶狀體表面進行碳、鈦材料修飾,對表面修飾的人工晶狀體進行表面特性的檢測。
- Preparation of Chromium Coating on Mo Substrate by Low Pressure Plasma Spraying and Wear Resistance of the Coating 低壓等離子噴涂鉻涂層的性能表征
- A STUDY ON THE ELECTRIC PROPERTIES OF TITANIC OXIDE COATING IN LOW PRESSURE PLASMA SPRAYED WITH TiO_2 低氣壓等離子噴涂TiO_2時涂層的電學性能研究
- Sealed under low pressure or a partial vacuum. 抽空密封的在低壓或部分真空狀態下密封起來的
- DLC films were prepared on silicon by pulse-arc plasma deposition. 利用脈沖多弧離子鍍技術在硅基底上沉積類金剛石薄膜。
- The barometer recorded a low pressure. 氣壓表標明有一低氣壓。
- low pressure plasma spray 低壓等離子噴涂（LPPS）
- DLC films have been prepared on silicon by pulse-arc plasma deposition. 利用脈沖多弧離子鍍技術在硅基底上沉積類金剛石薄膜。
- Water supplies to the house are at low pressure. 這房子的供水水壓低。
- Low Pressure Valve Options and Accessories Misc. 低壓閥門備選件和附件。
- Piston cooling oil inlet low pressure slow-down. 活塞冷卻油入口壓力低降速。
- Cylinder liner water inlet low pressure slow-down. 缸套水入口壓力低降速。
- low pressure plasma spraying 低壓等離子噴涂
- Low pressure mold closing is standard . 低壓開關模裝置可保護模具的安全。
- High and low pressure spay gun with adiabatic grip. 高低壓可調水槍?zhuān)罒針尡?/li>
- Plasma deposition dieless manufacturing(PDM) is a rapid heating and solidification process,in which how to avoid cracks and distortions is a key problem. 等離子熔積無模成形是急速加熱快速凝固的短流程制造技術,如何避免制件的熱裂紋是該技術的關鍵,而熱裂紋的產生取決于成形過程溫度場與應力場的分布特征。
- Low pressure thernostatic nixing palpes. 參考名稱: Sanitary tapware.
- Reasonable butyl spreading system and low pressure. 出膠系統合理，壓力低。
