您要查找的是不是：
- Bend the test piece 180 degrees over a mandrel with its longitudinal axis normal to the axis of mandrel. 將測試件在一根芯軸上彎曲180度，使其縱向軸線垂直于芯軸的軸線.
- Mm. B: bond surface of test piece: 50mm in width. 試件粘合面寬度50。
- Take arithmetic mean value of individual value of 5 test pieces in longitudinal or transverse directions respectively as the test result. 分別計算縱向或橫向5個試件的算術平均值作為試驗結果。
- Take the mean value of dimensional change rate of the 3 test pieces in longitudinal or transverse directions as the test result. 分別計算3塊試件縱向或橫向的尺寸變化率的平均值作為縱向或橫向試驗結果。
- The secondary factors are the number of holes and perforating rebar, the size of each test piece and so on. 其次是每個試件的孔洞個數和貫通鋼筋個數以及試件尺寸等。
- If an overall pattern (sometimes circular lines) appears on the test surfaces, how should the inspector reprocess the test piece? 如果零件上出現遍及表面的顯示(有時是環形線)，檢驗員應如何重新處理零件？
- The formularies and can be received and used to describe the influence of the placed time of sawed test piece to the plywood formaldehyde emission. 凱爾文模型較好地模擬了膠合板甲醛粘彈性釋放特征；
- Fees for Chromatic Harmonica Solo (Open Section) and Tremolo Harmonica Solo (Open Section) include the cost of one copy of the test piece. 半音階口琴獨奏公開組及複音口琴獨奏公開組之報名費已包括指定樂曲樂譜一份之費用。
- The scientists tested pieces of Beethoven's hair. 科學家檢測了貝多芬的幾根頭發。
- The mica test pieces were prepared by cleavage so as to be atomically smooth. 云母試樣是用劈裂的方法制備的，因此可以達到原子級的平滑程度。
- In this paper, the influence of heredity factors, such as the temperature and over cure temperature of hot metal, the addition of fine grain test piece and its lasting time in hot metal on ZL201 alloys are investigated. 研究了合金出爐溫度、熱溫度、晶粒試樣加入量及其在熔體中的停留時間等遺傳因素對ZL201合金熱裂傾向性的影響。
- Unless otherwise specified, the notched-bar impact work shall be verified on every forging or test piece by notched-bar impact-bending tests. 除非有其他規定，必須在每個工件和試驗件上進行切口沖擊試驗和彎曲試驗，以證明其符合試驗要求。
- This test piece shall be welded using the identical welding parameters as the original test and only weld metal impact test specimens shall be tested. 此試件應使用與原始試驗相同的焊接參數進行焊接，并且僅對焊接金屬沖擊試樣進行試驗。
- Ferrous sensitivity test piece shall be placed on top of the finished product/in tray of IQF fillets and passed under the detection head in the same orientation as standard product. 鐵敏感測試片應放置在生產完成的產品頂部/IQF魚片托盤中，在相同方位通過探測頭下的才是符合標準的產品。
- A simple test will show if this is real gold. 簡單的試驗就能證明這是否是真金。
- The author finds out through hisexperie nces a method for insuring the attitude of testing piece and inspecting theattitude errors of testing piece. 筆者在實踐中總結出一種保證試件姿態和檢驗試件姿態誤差的具體方法。
- A longitudinal cut from the trunk of a tree. 料板，板皮從樹干上縱切下的一塊木材
- The elastic-plastic finite element analysis (FEA) of typical testing piece with circle hole was carried out by FEA software ANSYS. 摘要應用ANSYS有限元軟件對典型構件圖孔板進行了彈塑性有限元分析有限元牽與解析解，說明ANSYS輔件計算的可靠性和準確性。
- A simulator can be used to test pieces of the software before the embedded hardware is available. 仿真器一般用來測試嵌入式硬件可用之前的軟件。
- The surface temperature change of Al test pieces in H2SO4solution during composite anodizing is researched. 研究鋁在硫酸溶液中復合陽極氧化時的鋁試件表面溫度的變化行為。
