您要查找的是不是：
- It can work steadier to adopt hydraulic balanced axial force. 采用水力平衡軸向力，減少平衡鼓，可使運行更為平穩。
- Further study indicated that cross beams and axial forces have great influence to the shear lag effect of longitudinal box girders under full dead load. 進一步的研究表明，在恒載作用下該橋縱梁的剪力滯效應受橫梁、軸力的影響很大。
- The planimetric position of the piles which endure the extremum axial force is different. 受開挖區域的影響，承受軸力最大值、最小值樁體的平面位置是變化的。
- This method is applied to analyze the lateral force of bit linearly with the nonlinear axial force being considerated. 考慮軸向力的非線性影響，應用該方法對底部鉆具組合的鉆頭側向力進行了線性分析。
- The effects caused by a axial force and the waveness in the surfaces of innerring are analysed. 本文主要對砂輪不平衡量引起的磨削表面波紋度進行了理論分析。
- Overloading of axial force acted on working roll is the primary reason to cause the bearing damage. 工作輥軸向力過載是導致軸承燒損的主要原因。
- This paper analyzes the effect of negative friction on pile s axial force and its calculation. 分析研究負摩擦力對樁軸力的影響及基樁負摩擦力的計算。
- Hydrostatic bearing can solve the equilibrium problem of axial force of multistage centrifugal pump satisfactorily. 液體靜壓支承技術可以很好地解決多級離心泵軸向力的平衡問題。
- This paper defines neutral section and neutral point respectively with effective axial force and ac. 本文還用有效軸力和真實軸力分別定義了中性截面和中和點。
- The incremental axial force of pile rises to 14kg when the surcharge increases to 1kg/cm2. 而摩擦樁試驗中，由于樁體產生較大沉陷量，而拉高中立點位置，使負摩擦力影響范圍減少。
- The mechanics models of metal-bands transmission concerning clamp force of pulley, axial force, thrust and tension is built based on Coulomb friction theory. 以庫侖摩擦理論為基礎，在考慮了帶輪夾緊力、軸向力、擠推力和金屬環張力的基礎上，建立了金屬帶傳動的力學模型。
- And axial force is applied to adobe masonry specimen, which are laid by varies marshaling way, to study their axial compression performance and failure forms. 使用不同的砌筑方法砌筑土坯砌體試件，對試件施加軸心壓力，研究砌體軸心受壓性能、破壞形態；
- Under axial force, moment and shear force steel-concrete joint subjected to compressive stress, tensile stress and shear stress. 在軸力、彎矩和剪力的作用下，鋼-混凝土接頭處將產生軸向壓應力、拉應力和剪應力。
- Axial force is balanced by back vane or balanceable hole, for the specification with big radial force; we adopt double-wear passage design. 軸向力由副葉片或平衡孔平衡，對于徑向力在的規格采取了雙殼體設計；
- Transmitted torque,thrusts of driving and driven pulleys,and axial force between two pulleys were measured on a metal pushing V-belt type CVT. 本文在金屬V-帶推塊型CVT上，測出了主、從動帶輪的傳遞轉矩和推力以及兩帶輪間的軸向力。
- Axial forces in the three working rollers reaches maximum at startup. 三個工作輪的軸向力隨著變矩器的工況變化，在起動工況時達到最大值。
- The bending moment,axial force of the pile and subfloor are also analyzed.Then it draws some conclusions useful to practical engineering. 對開挖引起的地面、建筑物角點的沉降規律做了分析與探討,同時也分析了樁和底板的彎矩、軸力、剪力等變化規律,得出了有意義的結論。
- A computing method is presented for studying the bending moment, axial force and curvity relationship at the section of prestressed concrete beam. 提出預應力砼截面彎矩-軸力-曲率關系的計算方法，并計算了不同預應力度下截面的彎矩-曲率關系。
- Analytic solution is established to describe axial force distribution of strings helical buckled in vertical wells when slack down from the top. 用解析法建立管柱下放時的軸向力表達式,得出軸向力極限值。
- The full-scale model tests of unstiffened steel tubular X-joint under axial force,bending and torsion conditions are presented in the paper. 介紹了雙向貫通式節點在軸拉(壓)、彎扭作用下的足尺節點試驗研究。
