您要查找的是不是：
- According to relationship between the capacitances,the liquid level, the permittivity and the inclination angle,thr... 從推導結果來看,它是一個簡單而實用的好方案,是值得去產品化的。
- The measurement of the inclination angle and the azimuth angle of a well in the drilling process is important. 鉆探過程中鉆井的傾斜角和方位角的測量至關重要。
- In this paper, spider die is analyzed in different conditions of inclination angle, compression angle and land length by computer simulation. 本文通過對支架式管機頭的在不同的分流角、壓縮角和定型段長度下的流場進行分析，從而得到每種參數發生變化時對流道流場參數的影響，指導機頭的設計。
- This study suggests a admissible load designing method, which leads out a series of calculating formulas based on the parabola theory and works out a value table for loaded rope to establish a systematic admissible load designing method. 本文提出許用荷重設計法,在拋物線理論的基礎上推導出一系列計算公式,編制承載索數值表,建立起系統的許用荷重設計方法。
- The influences of working fluid, Fill Ratio of liquid and inclination angle on the thermosyphon operating were analyzed. 試驗發現工質為水的熱虹吸管的啟動時間大于工質為酒精的熱虹吸管；
- Severe slugging usually occurs in a gas-liquid two-phase flow system where a riser is followed by a pipeline segment with a downward inclination angle. 嚴重段塞流主要出現在下傾管段、緊接有一上傾管段或立管段的氣、液兩相混輸海底管道中。
- In this article passive location with inclination angle is presented, and when radars in different altitude this algorithm is mended. 介紹了傾斜角定位算法的基本原理,并推導了處于不同高度雷達站計算傾斜角的公式。
- In this paper, a new proposal for multifunctional sensor measuring liquid level, permittivity and inclination angle is presented. 該文提出了一個可用于多功能傳感器的新方案。
- A lowest input heat power was needed when the thermosyphon started and the limited heat transfer rate was found under any inclination angle. 隨著熱虹吸管加熱段溫度升高，整體振蕩的周期有縮短的趨勢。
- On the condition of a larger pipe inclination angle, the distribution of liquid slug lengths was more concentrated in a smaller range. 在管線下傾角較大的情況下，液塞長度分布集中在較小的范圍內。
- The distribution of chip thickness along the cutting edge is modeled as a function of tool inclination angle,nose radius,depth of cut and feed rate. 沿切削刃切屑厚度的分布,被作為刀具刃傾角、刀尖圓弧半徑、切削深度和進給量的函數被建模。
- The functions of cutting edge inclination angle were expounded in this paper,Selection principle and its reference quantity were sumed up also. 本文對刀具刃傾角的功用進行了較詳細的闡述，并歸納出了其合理選用的原則和參考值。
- When the mixture velocity is high enough, the flow tends to axisymmetrical so as to the influence of tube inclination angle can be neglected. 在高混合物流速下，流動趨于軸對稱，此時可忽略?xún)A角的影響。
- It can increase the hole inclination angle range and drill elevation angle holes, while setting the top drive power head and hole top plate toward the opposite direction. 動力頭及孔口板調轉方向,可直接鉆鑿仰孔,大大增加鉆孔傾角范圍。
- The effects of tool's inclination angle on chip formation and the temperature fields,as well as the cutting forces,back forces and feed forces are discussed. 通過三維切削模擬可以獲得在不同刃傾角精密切削過程的條件下切屑形狀、切削力和切削溫度場的分布情況。
- Too heavy a load will strain the rope to its breaking point. 負載過重會(huì )把繩子拉緊到崩斷的地步。
- On restraining the backmixing of particles across baffles, baffles with more layers, with lesser vane gap and with lesser inclination angle of vane will be better. 較小的葉片間距將有助于破碎氣泡，也有助于抑制顆粒軸向的返混；較小的葉片傾角將有助于抑制顆粒軸向的返混，但對氣泡破碎的影響不大。
- The ship was loaded with cargo fore and aft. 這條船從船頭到船尾裝滿了貨物。
- The result shows that the synthetic jet actuator with an inclination angle can effectively control low speed primary jet vector and the primary jet direction can be changed greatly by altering the angle without increasing input power. 結果顯示,激勵器出口傾角對主流矢量角控制影響很大,在不增加輸入功率的情況下,可使主流流動方向發生大幅度偏轉。
- As the inclination angle is varying, the wall superheat for the same heat flux is varying accordingly, and the role of the sliding bubbles and the microfilm evaporating mechanism in these channels is also different. 加熱面所處角度不同 ,在相同熱負荷下壁面過熱度亦不同 ,滑移汽泡和微液膜蒸發機理在通道中發揮的作用也相應不同。
