您要查找的是不是：
- Install adjuster nut and lock nut. 安裝調節器螺母和防松螺母。
- Lock handle securely by turning lock nut clockwise. 3、順時針?lè )较驍Q緊螺帽，可靠的鎖好把手。
- To Readjust- Loosen lock nut on the adjusting screw. 重新調節：松開調節螺絲上的鎖定螺母。
- To Readjust - Loosen lock nut on the adjusting screw. 重新調節：松開調節螺絲上的鎖定螺母。
- Revolving the lock nut 5 anti-clockwise to the suitable position. 逆時針?lè )较蛐D鎖緊螺母5;使其退到適當位置.
- Disc is fastened securely to disc hanger with a lock nut and cotter pin. 通過一個鎖緊螺母和開口銷將閥瓣安全緊固在閥瓣支架上。
- If only one locating ring is required, it should be inserted on the same side as the lock nut. 如果只需一個定位環,此定位環應插入與鎖緊螺母相同的一側。
- The first product we developed and completed based on this theme was the Hard Lock nut. 我們以此為出發點,開始了研究開發,經過不斷實驗終于研究成功了Hard Lock螺母。
- Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening angle. 孔徑最大為100毫米的小型軸承可通過測量鎖定螺母的緊固角度正確安裝。
- To replace diaphragm; loosen lock nut (48) and remove lock washer (46), diaphragm plate (60) and diaphragm (20). 要更換隔膜，先松開鎖緊螺母(48)，并拆卸鎖緊墊圈(46)，隔膜板(60)和隔膜(20)。
- Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem. 松開和拆卸隔膜鎖緊螺母和鎖緊墊圈，從閥桿上往下壓閥盤和隔膜。
- Remove spring cage, spring and washer. Remove bottom plug. Grasp upper and lower stem lock nut with wrench and loosen. Clean or replace any damaged or worn parts. 拆卸彈簧籠，彈簧和墊圈。拆卸底部塞。用扳手抓住上部和下部閥桿鎖緊螺母并且松開。清洗或更換任何損壞或磨損部件。
- The feasibility of repetitive use of Fe-based shape memory alloy lock nut has been studied in order to lower the usage cost. 為了降低鐵基形狀記憶合金防松螺母的使用成本,探索了該新型螺母重復使用的可行性。
- Remove the locking nut from the flow/conductivity/temp sensor. 移開流量/導電/溫度傳感器上的固定螺絲。
- Remove the locking nut from the flow / conductivity / temp sensor. 卸除流量/電導/溫度傳感器上的鎖緊螺帽。
- Measuring the lock nut tightening angle is a proven method to determine the correct degree of interference in small to medium-sized bearings on tapered seatings (fig). 測量鎖定螺母的緊固角是經驗證的有效方法,可用來確定圓錐軸頸上中小型軸承的正確過盈度(圖17)。
- Balancing wrench in left hand with graduations visible with the marked arrow elementary scale up, unlock knurled handle by turning lock nut counter-clockwise. 1、平衡扳手的左手有可見的分度和按比例放大的箭頭標記，按逆時鐘方向滾動鎖緊螺帽，開啟有刻度的把手。
- Jack was assigned to the assembly shop of the factory. 杰克被分配到廠里的裝配間工作。
- I am longing to see my friend Jack again. 我渴望再見到我的朋友杰克。
- He has no intention to jack up the plan. 他沒有放棄這個計劃的意思。
