您要查找的是不是：
- Do you know how to patch an inner tube? 你知道怎樣修補內管嗎?
- The tyre and the inner tube are both punctured. 外帶和里帶都扎穿了。
- This truck's inner tube is broken. Help me to mend it, please. 這部車的內胎爆了,請幫我補一下好嗎?
- The sport or recreation of floating down a stream or river in an inner tube. 漂流乘皮艇順水流或溪流飄浮的運動或消遣
- The inner tube of the tire should be changed. Now it leaks air badly. 這個輪胎該換里帶了，現在漏氣漏得厲害。
- GT express inflating system can inflate the inner tube ofa tyre in an instant. GT快速充氣系統瞬間為無內胎輪胎進行快速充氣。
- Wire plate keep a certain height with ground , manually through the guide wire to wire to wire feeding tube body. 焊絲盤離地保留一定高度，通過人工把焊絲穿過導絲管送到送絲機構。
- Using a small ax, I cut an old inner tube into the shape of the sole and put holes in the rims of the shoes with an ice pick. 我按照鞋底的形狀，用一把小斧子從一個廢舊的車子內胎上切下一塊膠皮，又用一個破冰鐵鑿沿著鞋邊鑿了洞眼。
- The yield strength decrease of SSAW and ERW tube body can be attributed to both Bauschinger Effect and high springback stress incurred by manufacturing process. 制管過程中的包申格效應及制管過程中引入的高彈復應力 ,使螺旋焊管及直縫焊管管體屈服強度明顯低于板卷屈服強度。
- This coated inner tube is closed at one end and sealed at the other end to the outer tube. 內管的涂層是介于一端與另一端的外管的密封層里面。
- For UOE tube with low springback stress,the Bauschinger Effect makes the yierld strength of flated specimen be lower than that of UOE tube body which received expanding process. 對UOE管,由于其彈復應力低,包申格效應使壓平試樣的屈服強度低于經強力擴徑強化的管體屈服強度,因而這種表征是偏于安全的。
- In humidifier add enters the perfume with oily blame, can come a few minutes to domestic inner tube romance and warmth. 在加濕器里兌入非油性的香水，可給家里帶來幾分浪漫和溫馨。
- Mainly by motor, framework, other tube body, put on, turn tube, empty mandrel, big gear wheel, pinion, move it jaw board and quiet jaw board make up round in grades. 它主要由電動機、機架、外筒體、分級罩、回轉筒、空心軸、大齒輪、小齒輪 、動顎板和靜顎板組成。
- By replacement of rotary kiln tube body section solves the problems brought by ageing equipment,such a replacement with simple process and low engineering cost. 通過對回轉窯筒體實施截體更換，解決了設備老化帶來的問題，而且工藝簡單，工程成本低。
- When the dryout point occurs on the inner tube, the critical heat flux will increase with the decrease of curvature. 內管干涸時，臨界熱流密度隨曲率的減小而增大；
- Heat transfer enhancement was investigated in a coaxial-pipe heat exchanger using dimples on the inner tube. 在換熱器管道的內壁面上布置丁胞可以有效地增強管道內的傳熱。
- Fricton reduction mecha nism and technical properties of the inner tube analysed. 對內筒減阻原理及技術性能進行了分析。
- USE: The machine is used for the extrusion of half-finished rubber products such as tire tread, inner tube, rim band and rubber tube. 本機用于擠制胎面,內胎,墊帶,膠管等橡膠半成品。
- The annular space between the outer tube and inner tube is evacuated to virtually eliminate heat loss by conduction and convection. 而介于外管與內管的真空環狀部分是用來減少熱散失的。
- By means of theory calculating and analyzing,increasing steel ball section and reality filling up rate(from 26% to 46%),raising tube body speed(from 26.1r/min to 37.3r/min),main bearing from sliding bearing changed ball-bearing are used. 通過理論計算與分析;采取了加大鋼球(段)和實際充填率;由26%25增加到46%25; 提高工作轉速;由26.;1r/min加快到37
