您要查找的是不是：
- Close the cold water inlet valve and open a nearby hot water faucet. 關閉冷水進水閥，打開附近的熱水水龍頭。
- Studies on Steady Measurements of In-Cylinder Tumble in a 4-Valve Engine with One Inlet Valve Opening 4氣門發動機單氣門工作時缸內滾流運動的穩態測量研究
- If the drain hose does not have this rating, open the cold water inlet valve and open a nearby hot water faucet until water is no longer hot. 如果排水軟管的額定溫度沒有達到上述要求，請打開冷水進水閥，打開附近的熱水水龍頭，直到水不熱為止。
- The tightness test of inlet valve for emergency fire pump. 應急消防泵進水閥密性試驗。
- The vacuum valve opens to admit air. 真空閥開啟以補充空氣。
- The valve opens for tank discharge when tank head pressure is greater than valve inlet pressure. 當容器水頭壓力大于閥門進口壓力時，閥門開啟進行容器排放。
- Lift retainer and check assembly from valve body. To assist with removal a small flow can be applied by "cracking" the inlet valve slightly. 從閥體內取出固定器和止回模塊?？梢酝ㄟ^(guò)稍微“開裂”閥門進口來幫助清除少量的流體殘留。
- When the coid is powered the valve opens (t< 1s). 當切斷電流時，閥門迅速關閉。
- To assist with removal a small flow can be applied by "cracking" the inlet valve slightly. 為了有助于拆卸，可以通過輕微"分裂"閥門進口來產生一小股流體。
- Hydrostatic pressure testing of the inlet valves (with open and closed disc) under a pressure of 1,5 times the maximum static pressure plus water hammer for 30 minutes. 持續30分鐘1.;5倍的最大靜壓與水錘壓力下，對入口閥（帶打開和關閉盤）的靜水壓試驗
- When the piston nears the top of this stroke, the inlet valve is opened and the exhaust valve closed. 隨著曲軸轉動，復又向上帶動活塞，同時廢氣經由氣缸頭蓋上的排氣閥排出。
- So the exhaust valve opens before BDC and closes after TDC. 因此排氣門在下止點之前打開，在上止點之后關閉。
- The outlet valve of the plunger pump must be taken down before the inlet valve is hauled out with the former disassembling instrument for the valve. 柱塞泵的下凡爾損壞后,用原來配的凡爾拔出器拆卸時要先拆掉上凡爾,再拆卸維修下凡爾。
- If the valve fails to completely reset and continues to release water, immediately shut off the cold water inlet valve, and call a qualified service technician. 如果閥門無法完全重置，并繼續釋放水，則要立即關閉冷水進口閥門，打電話叫有資格認證的工程師。
- Chemical analysis and mechanical tests on the materials used for inlet valve body, disk, trunnions, servomotor cylinders, piston rods, upstream and downstream piping. 對用于進氣閥閥體、閥盤、耳軸、伺服缸、活塞桿及上下游管道的材料進行化學分析和機械測試。
- Meanwhile, the problem of fast open/close of air inlet valve during air surge backwash and some default of equipment was successfully solved during commissioning. 在調試中，解決了水氣反洗時要求進氣閥快速開／關等問題。
- By applying black box theory inlet pressure, inlet subcooling, outlet pressure and valve opening are selected as influence factors to flow coefficient of electronic expansion valve (EEV). 根據黑箱理論提出將閥前壓力、閥前過冷度、閥后壓力和膨脹閥流通面積作為膨脹閥流量系數的影響參數。
- Valve opens when control switch is open 5-seconds and closes when control switch is closed 5-seconds. 當控制開關開啟5秒鐘時閥門就開啟，而當控制開關關閉5秒鐘時閥門就關閉。
- One, why is a small two-seater valve opening oscillation work easier? 為什么雙座閥小開度工作時容易振蕩？
- The intake and exhaust valves open at the proper time to let in air and fuel and to let out exhaust. 吸氣閥門和排氣閥門在正確的時間打開，以使空氣和燃料進入，以及使廢氣排出。
