您要查找的是不是:
- To extend mould utility longevity, to shorten injection cycle. 提高模具的使用壽命,縮短注塑成型周期。
- To extend mould utility longevity, to shorten injection cycle. 提高模具的使用壽命,縮短注塑成型周期。
- Laboratory experiment of dry gas injection in super low-permeability carbonate fractured reservoir. 裂縫性特低滲碳酸鹽巖油藏注烴類氣驅油室內實驗研究。
- Gas injection adjustment -: This function of the button is doing reduce action for what it chose area value. 本按鈕的功能是將所選區域的值進行減動作。
- A complete set of EOR technology by gas injection in low permeability oil reservoirs. 低滲透油藏注氣提高采收率配套技術
- We used long cores in order to get hydrocarbon gas injection EOR efficiency , and got PVT parameters . 在室內開展了注烴氣的長巖心驅替試驗,用物理模擬的方法研究了注烴氣提高采收率的幅度,并取得了流體的PVT參數;
- During IOR by gas injection, asphtene precipitation will commonly block the effect of IOR. 在注氣提高采收率過程中,瀝青沉降經常嚴重妨礙了采收率的提高。
- Gas injection mechanism in buried hill reservoir has been studied through analyzing the impact of gas on oil PVT. 通過分析天然氣對原油高壓物性的影響,研究了古潛山油藏的注氣機理。
- The enhancement of convective heat transfer is more obvious than that of subcooled flow boiling by inert gas injection. 結果表明:混合對流傳熱時,傳熱的增強更加顯著,引入惰氣對對流傳熱的增強程度要明顯好于對過冷沸騰傳熱的增強。
- Jakobsson NM ,Christian T M. History performance of gas injection of ekofisk[C] . SPE 28933. 李留仁;趙艷艷.;低滲透油田注水與注氣開發數值模擬比較[J]
- This study provides a theoretical basis and experimental data for enhancing coalbed methane recovery by gas injection. 本工作為煤層氣注氣提高采收率提供了理論依據和實驗數據。
- Gas injection flooding as an important method of EOR has been researched and applied on a large scale in both laboratory and field. 注氣驅油作為提高采收率的一種重要方法,國內外已在實驗室和現場進行了相當規模的研究和應用。
- The operative principle of gas assisted injection molding and the structure components of gas injection machinery are analyzed. 介紹了氣體輔助注射成型技術的工作原理,氣體注射裝置的基本組成系統。
- Dry gas injection huff and puff is one of the effective techniques to remove the retrograde condensate blocking of condensate gas wells. 注氣吞吐是解除凝析氣井單井反凝析油堵塞問題的有效方法之一。
- Gas injected PEX? dielectric for accurate signal transfer, even over long runs. 專利的PEX?氣體電介質注入技術令到信號傳輸精確;經久耐用.
- It was found that gas injection at riser base could eliminate the severe slugging and stabilize the gas and liquid flow rates at the riser outlet. 實驗結果表明,采用上升管下部注氣的方法可以消除嚴重段塞流現象,實現管道出口氣液的穩定流動,減小系統的最高壓力,同時可以防止上游水平管內出現高頻率的長液塞流動。
- Conclusion Liguid or gas injection to anterior chamber can make the crystalline lensiris move formard and return to normal position,maint... 結論前房注氣注液(或黏彈劑)可使前移的晶狀體_虹膜隔恢復原位,維持眼內壓力,使房水循環恢復正常從而治愈脈絡(luò )膜脫離。
- The result indicated that GAE could reduced the pressure drop and moved the local exit stress concentration to the point of gas injection. 研究表明:氣輔擠出可以降低壓力降,將應力集中的位置由口模出口處轉移到氣體的注入點;
- This paper defined natural gas injection point and injection direction for Wenliu gas field combining with gas source correlation tracing. 通過對文留氣田天然氣氣源對比追蹤,確定了該氣田天然氣充注點和充注方向;
- Abstract: Research for bow shock due to secondary gas injection was developed with different points of injection,Mach numbers and jet angles. 文摘:研究了不同噴射位置、噴射馬赫數和噴射角度的氣體二次噴射混合流場的弓形激波形狀。