您要查找的是不是：
- Head dresser is secured high surface rough. 高精粗糙度修整裝置。
- It is brittle and breaks with a conchoidal fracture surface. 性脆，具貝殼狀斷口。
- Table 1-2 Surface roughness and chrominance of treated wood. 表2處理材于水質環境下經長期試驗后防腐劑之保留率.......57
- Surface roughness has a profound effect on wind speed. 地表粗糙度對風速有相當深刻的影響。
- A New Noncontact Method for Rapidly Measuring Surface Roughness[J]. 引用該論文 胡克平;李田澤.
- The fracture surface traverses matrix as well as fibers and interface. 斷裂表面橫切過基體、纖維和界面。
- Sandblasting to achieve the desired surface roughness. 清潔輥筒表面，邊緣倒角。
- The adding of POSS in the polymer lowered the surface roughness. 添加POSS后聚合物表面粗糙度減小。
- The state of knowledge about fracture surfaces is very meager. 有關斷裂表面的知識非常缺乏。
- Effects of different preparation procedures on abutment surface roughness. 不同預備程序對基牙表面粗糙度的影響。
- Grainy edge Surface roughness on edges of web caused on the drying process. 起皺紙邊紙卷邊緣在乾燥過程所引致的起皺情況。
- Grainy edge: Surface roughness on edges of web caused on the drying process. 起皺紙邊:紙卷邊緣在干燥過程所引致的起皺情況。
- Surface roughness of the MSD MCrA1Y coating is far lower than the one of LPPS. MSD的MCrA1Y涂層表面粗糙度遠比LPPSMCrA1Y低。
- The microstructure and tensile fracture surface of the Q235 steel has been investigated by TEM and SEM. 應用TEM和sem觀察鋼的微觀組織結構及拉伸斷口。
- Problems such as drill life exit burr and machined surface roughness etc. 對采用超聲波振動鉆削微小孔時鉆頭的壽命、出口毛刺和加工表面粗糙度等問題進行了研究。
- The adiabatic heating induces the temperature of fracture surface layer to be higher than the liquidus temperature too. 計算表明;斷口表面層絕熱升溫溫度依然高于液相線溫度.
- Wood surface roughness was studied by using fractal dimension method. 應用分形維對木材表面粗糙度特征進行研究。
- Fracture surface was flat in macrographic view,but dimpled rupture was observed in micrographic view. 宏觀斷口都比較平坦，但在微觀上均呈現塑斷特征；
- Thirdly, microstrain-, peripherin-thick, surface roughness, resolution 3%. 不一是球磨砂綱，感平層不薄，暗地粗劣，分辨率3%25。
- The fatigue fracture surface of test specimens shows hybrid-fracture characteristics of quasi-cleavage and dimple. 合金中添加Ce后,疲勞裂紋擴展區出現疲勞條紋,疲勞斷口呈現出準解理和韌窩斷裂的混合特征。
