您要查找的是不是：
- Design of a Composite Hot Forging Die for Screw Plugs. 油孔螺塞拼接式熱鍛模具的設計
- Abstract The paper gives out structure of tilting pin type hydraulic forging die for producing frame of shaker. 給出了震動器機殼斜銷式液鍛模具設計結構。
- Through the analysis of hook, a reasonable forging process and forging die have been designed. The defects has been analyzed and solved. 摘要通過對吊鉤的工藝分析，設計了合理的鍛造工藝方案及其熱鍛模，并對出現的缺陷進行了分析解決。
- An investigation was carried out for the recondition of a mould for the forming of automotive plastic floor board and a half-axle swing forging die. 介紹了幾種典型模具快速修復工藝方法,并對汽車地板革成形模和汽車半軸擺動輾壓模的修復進行了研究。
- The dynamic stress concentration problems at the swallowtail on a hammer forging die are investigated by using the dynamic photoelastie method. 用動態光彈性法研究了錘鍛模燕尾的動態應力集中問題。
- Traditional forging die manufacturing including a lot of process and using EOM to form the impression results some disadvantages such as longer production time and higher cost. 摘要傳統鍛模加工，由于加工道次多，且需采用放電加工制造模穴，導致有制造時間長，且成本偏高的缺點。
- This paper introduced the inserted forging die,and the difficult point of its plasticity design. The main point of its plasticity design which can enlarge its function. 簡要地介紹了鑲塊鍛模結構特點和可塑性?xún)?yōu)化設計的難點;著重介紹擴大其使用性能可塑性設計方法的要點.
- The life of H13 steel forging die for link was studied,the relation of die life and die rigidity was discussed, the measures of increasing die life were brought forward. 研究了H13鋼連桿鍛模的壽命問題,討論了模具壽命與模具硬度的關系,提出了提高模具壽命的措施,設計了H13鋼連桿鍛模的最佳熱處理工藝。
- Analysis on forging technolgy of transverse arm part has been introduced, upon which technics flow of die forging has been designed, with design of forging die cavity. 通過對轎車左右橫臂的結構及鍛造工藝分析,制定了其模鍛工藝流程,介紹了模鍛工藝及其工步型腔設計。
- Analysis of Joint Type of Flanging Die Insert 翻邊凹模鑲塊交接型式的分析
- By improving the design of forging die and using press-forging and backward extrusion principle,solves the problems of 130 steering knuckle forming which can not be fully filled during forming. 通過改進預鍛模膛的設計,利用鐓粗成型、反擠成型的原理,有效解決了130轉向節板部模鍛成型時充不滿的問題。
- Because of the forming temperatures are different, the cooling of warm molding forging are distinguish from hot forging forming.The cooling method and design of warm forging die are introduced. 因其成形溫度的特點,對溫鍛模具冷卻有別于熱鍛成形。
- So it is significative to study the ICAD system of hammer forging dies for connection rods. 因此，連桿錘鍛模ICAD系統的研究就有了重要的意義。
- BOLT &NUT FORMING DIES,TUNGSTEN CARBIDE DIES,PRESSING DIES,FORGING DIES,PUNCHES,K.O.PIN.ALLOYSTEEL,TOOLINGS. 各種螺絲、螺帽沖壓成型模具、碳化鎢沖壓模具、合金鋼工具、模具、零件沖壓、鍛造模具。
- Die inserts, together with the cores which form recesses, must endure the effects of temperature and injection pressure of the molten metal. 與形式隱藏，必須忍受溫度和熔融金屬的射入壓力的作用的核心一起死插入物。
- Study on hardfacing technology of die insert and its application 大型鑲塊式修邊模具的堆焊工藝及應用
- A lever pattern of the ejetion mechanism was designed to solve the problem of the hot chain element being taken out from the air hammar forging dies. 針對鏈節胎模鍛存在起模困難的問題,設計了一套杠桿式頂出機構頂出制件,采用此機構可提高生產率,同時,減少了熱鍛件的悶模時間,提高模具的使用壽命。
- Insert a want ad, and it may help. 登一則招聘廣告，也許有用。
- Reproducing experiment was carried out on hot forging dies for connecting rods, to improve the service life of dies and decrease the cost of rods. 為提高模具壽命降低連桿生產成本，進行了連桿熱鍛模再制造試驗。
