您要查找的是不是：
- Apply the technique of CFD and FEM， advance the design of flow speed. 利用CFD(計算流體力學技術)，FEM(有限元技術)，提高設計流速。
- The SPL(Sound Pressure Lever) of flow-induced tones limits the required flow speed of aero-acoustic experiment. 為了在氣流當中進行噪聲測量,傳聲器上必須加裝適當形式的鼻錐以降低傳感器自噪聲。
- In order to measure the torque and rotational speed, changes the torque and the rotational speed signal into electric signal of two sine signal through the torque speed probe of Model JCZ. 摘要為了測量轉矩和轉速，將轉矩、轉速信號通過JCZ型轉矩轉速傳感器轉換成兩路正弦信號的電信號的進行測量；
- Under TCD display,record respectively the blood flow speed of the vertebrobasilar artery before and after observation. 觀察經顱多普勒(TCD)評估針刺百會(huì )穴對頸性眩暈椎-基底動脈供血的影響。
- Conclusion TCD showed functional diseases of psychosis are related to cerebral blood flow speed in a great degrees. 結論TCD檢測結果提示精神病人的功能性疾病在很大程度上與腦血流改變有關。
- On the other hand, subtidal flow speed is smaller but still toward the south during the summer southwestern monsoon. 而在夏天紊亂的風場中，流速相對較小，仍朝南流。
- The study also showed that the X-resin has greater sorption at pH6.0,concentration 30.12 mg/ml and flow speed 1.5ml/min. X-5樹脂在類黑精溶液pH為6;濃度為30.;12mg/ml;吸附流速為1
- The emphasis has been put on flow speed and flow rate required by recirculation detergent to clean pipes and filler bowl. 尤其對流動洗滌劑清洗管道和缸闡明了所需要的流速、流量。
- The construction diversion of the Tankeng Hydropower Station has the characteristics of big discharge and quick flow speed on its overflow cofferdam. 三峽工程導流底孔承擔三期導、截流和圍堰發電期泄洪任務，水頭高、流量大、運行條件復雜，為國內外導流工程罕見。
- It is first found that the major oscillating mode can switch to another frequency mode at small increase of incoming flow speed. 實驗發現了空腔流激振蕩的主導模態隨來流速度的敏感變化現象。
- Aim: To investigate the effects of Angelica sinensis injection on the ne uronal metabolites and blood flow speed within reperfusion in the ischemic cereb ral injury of rats. 目的:研究當歸注射液對腦缺血/再灌注時神經元代謝物及血流速度的作用,闡明當歸對腦缺血損傷神經修復過程的影響。
- In service pipeline non-stop transmission welding is a method to maintenance and rebuild pipeline under welding pipe of certain transmission amount,flow speed,pressure status. 在役管道不停輸焊接是在一定的輸量、流速、壓力的狀態下焊接管件,對管道進行維修、改造的一種方法。
- In dynamicexperiments,the effects of rhenium concentration and flow speed of the solution onadsorption,and flow speed of eluent on desorption are examined. 在動態試驗中，考察了溶液錸濃度、溶液流速和解吸劑流速的影響。
- It is concluded that the combustion chamber passage area, passage direction, passage shape and passage position have a strong effect on in-cylinder current motion and flow speed. 計算結果表明，燃燒室通道截面積、通道傾角、通道形狀、通道布置對氣流運動的形式及氣流速度均有較大的影響。
- Then, the flow speed is in line with flow rate and kept on without being affected by subsequent pipes, thus distributing uniformly the pulverized coal injected. 結果表明，在現有高爐噴煤系統的各輸送支管前安裝一組具有相同幾何尺寸的“喉形噴管”并滿足適當壓力條件時，兩相流將在各噴管內發生壅塞流動。
- The air flow speed change and the interactional situation between the aerosol particles and the wash solution resembles that in the venturi’s each corresponding part. 氣流在風機中的速度變化以及氣溶膠和洗滌液之間的相互作用狀況，與文丘里各段相似。
- In dynamic experiments,the effects of rhenium concentration and flow speed of the solution on adsorption,and flow speed of eluent on desorption are examined. 在動態試驗中,考察了溶液錸濃度、溶液流速和解吸劑流速的影響。
- Liquid chemical additives is low flowing speed, mild and undiluted chemical additives flow (eliminating diluted water). 化學品流體是低流速、溫和且未經稀釋的化學品流（不需要稀釋水）。
- TDS sho wed that the flow speed of base artery(B A) was increased littlely,the blood flow of left cerebral artery(LACA)was come b ack to well balance and no significant c hange in others at Finally 2 weeks. 兩周后 TDS檢測 :基底動脈 (BA)流速略有增加 ,左大腦前動脈 (L ACA)血流恢復至正常 ,其它未見明顯改變 ,統計學無顯著性差異。
- The selection of pipe wall thickness,the calculation and design key points of the melt flow,melt pipe flow pressure fall and melt flow speed in the design of melt pipes were introduced in detail. 介紹了熔體管道設計中管道壁厚選擇、熔體流量、熔體管道流動壓力降和熔體流速等計算方法和設計要點。
