您要查找的是不是：
- Determine installation direction of opening of piston ring as specified (see Figure 16). 活塞環開口安裝方向亦應按規定，見圖16。
- This paper analyses the patterns and reasons of piston ring wear and ineffectiveness and proposes some countermeasures. 本文對活塞環磨損失效的形式及原因進行了分析，并提出預防措施。
- The influence of sand & dust and low pressure on dynamics of piston ring was studied. 研究了西部低氣壓及沙塵環境對于活塞環動力學的影響。
- Employ various nitrding technologies including gas nitrding,ionitriding,brine nitriding to meet the specific situations of piston ring producion. 擁有多種氮化技術工藝包括氣體氮化、輝光離子氮化和鹽浴氮化，從而大大地保證了活塞環各環別采用最合理的處理工藝。
- Aiming at the problem of the low discharge pressure and unsatisfying air displacement of compressors,the material property and structure of piston ring is remoulded. 針對壓縮機排氣壓力偏低,排氣量達不到額定要求等問題,對活塞環的材質和結構進行改造,采用聚酰亞胺活塞環,保證了設備正常運轉
- Production of piston rings for hydraulic appl.;transmissions;compressors etc. 還生產用于液壓、傳輸和壓縮機等環境的活塞環。
- A new method to design the free shape of piston ring is described in this paper.Without the simplifications that adopted in the three traditional design methods,this method is of a high accuracy. 提出了一種新型活塞環型線設計方法，該方法未采用傳統3種設計方法的簡化過程及近似方法，故計算精度高；
- By analyzing heat transfer process of piston ring in a reciprocating compressor and considering the friction heat,the temperature distribution of a ring is deduced by an energy balance equation. 通過分析活塞壓縮機活塞環的傳熱過程,并將摩擦熱計算在內,利用能量平衡方程推導活塞環的溫度分布。
- They are most graphite cast iron and steel.The performance of piston ring can be improved by surface treatments such as plating chromium,nitriding,spraying molybdenum and spraying ceramics. 球墨鑄鐵和鋼材已經成為活塞環的基本材料,采用表面處理方法如鍍鉻、氮化、噴鉬、噴涂陶瓷層等工藝進行表面改性來提高活塞環的使用性能。
- Inoculation effects of RE-containing inoculant used for cylinder castings of piston rings was studied. 研究了稀土復合孕育劑在灰鑄鐵筒體活塞環中的孕育效果。
- An instrument that measures the outer profile parameters of piston rings such as conical rings, tubbish rings by scanning is introduced. 介紹一種采用掃描方式測量錐面環、桶面環等活塞環外圓輪廓參數的測量?jì)x。
- The results show that the nitriding distortion of piston rings is mainly caused by the residual compressive stress in nitrided case of the external circle working face. 結果表明,活塞環的滲氮畸變主要是由于活塞環外圓工作面滲氮層的殘余壓應力導致。
- Application of Piston Ring Shot-blasting Machine 活塞環專用拋丸機的應用
- Process of Outer Surface Treatment of Piston Ring 活塞環外表面處理工藝
- Study on Increasing the Service Life of Piston Ring 淺談提高活塞環使用壽命的方法
- Measurement of Closed Gap of Piston Ring 活塞環閉口間隙的測量
- Quality Control of Piston Ring for High-duty Engine 高負荷工程機械發動機活塞環的質量控制
- Quick Detection of Free Placket of Piston Ring 活塞環自由開口、搭口長度的快速檢測
- Effect of Piston Ring on Engine Oil Consumption 淺談活塞環對發動機油耗的影響
- The tilt and flex Of Lexus LS400 steering wheel can be controlled by ECU. 凌志LS400汽車方向盤可利用電腦ECU控制方向盤伸縮與傾斜。
