您要查找的是不是：
- A Pump-circulation Plug-in Engine Block Heater and its Preheating Start Test 一種泵循環機體電預熱器及其預熱啟動試驗
- Insert block heater assembly into core hole with element loop pointing Up. 將電熱器組合插入中心孔，元件環 向上。
- The large amount of heat generated by the engine block has to be dissipated. 由發動機組產生的大量的熱必須散出去。
- Some engine blocks are made entirely of aluminum. 而有些氣缸體完全由鋁做成。
- The oil passages in the cylinder Block should be cleaned out as part of the engine Block Service and Maintenance job. 在檢修發動機時,應對缸體中的油道進行清潔保養。
- The tappet hole of D6114 diesel engine block is machined difficultly and has high design requirement on accuracy. D6114柴油機機體挺柱孔加工難道大、加工精度要求高。
- The camshaft also can be located in the lower part of the engine, within the engine block. 凸輪軸也裝在發動機底部的氣缸體內。
- They were later chained still alive to an engine block and drowned in the Mississippi. 后來他們被活活地用鏈子拴在發動機組上并投入密西西比河淹死。
- Mostly into engine blocks, wheels, suspension components and hoods. 主要是到發動機組，輪轂，懸掛部件和遮光罩。
- Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware. 產品/Product：汽車發動機缸體、缸蓋、軸承蓋、渦輪增壓器殼體、排汽歧管、柴油發動機鑄件、槽盤。
- The engine block also holds the crankshaft, which fastens to the bottom of the block. 曲軸也固定在氣缸體底部。
- This dissertation addresses the measurement method of car underpan, white car body and engine block using CMM in car inspection product line. 本文正是在這一前提下研究了三坐標測量機在汽車底盤、白車身、發動機檢測時的不同特點，提出了三坐標測量機在汽車生產線檢測時的測量方法。
- According to modified engine block computer model, redid FEA to test and verify the result showed that after modification. 根據改進后的機體計算機模型進行有限元重分析,驗證機體改進的效果。
- Production processes, costs, and sub-contractors will be identified to allow short-term mass-production of the entire MCE-5 VCR engine block. 生產工藝，成本，及分包商將確定允許短期大規模生產的整個德育- 5錄像機發動機缸體。
- In this paper, the mode character of MWM395 engine block is analyzed with the finite element analysis on the platform of I-DEAS. 本文應用有限元法在I-DEAS軟件平臺上對MWM395柴油機機體進行了模態分析。
- The paper presents the main points ofshell core design of engine block for the diesel engine,problem prevailed,solving method,etc. 介紹了殼芯工藝生產柴油機機體殼芯的設計要點、出現問題及解決方法等。
- He is a great guy, a chip off the old block. 他是一位好人，就像他父親一樣。
- In the combination splash and pressure feed lubricating system, an oil pump takes oil from the oil pan and forces it through holes drilled in the engine block and crankshaft. 在飛濺與壓力結合式送油潤滑系統中;油泵從油盤中把油抽上來并壓入發動機機體上和曲軸上的油道中.
- The noise radiation of internal combustion engine block was calculated by multi-body system simulation (MSS), finite element method (FEM) and boundary element method (BEM). 摘要結合多體動力學仿真技術與有限元法(FEM)和邊界元法(BEM)對一臺4缸發動機的機體噪聲輻射進行了預測。
- The test of water simulation on the original running system verifies shows that unreasonable original running system causes blow hole in 495A diesel engine block casting. 通過對缸體原澆注工藝的水力模擬,發現原澆注工藝不合理是造成495A缸體產生缺陷的主要原因。
