您要查找的是不是：
- Photographing and Dynamical Dealing in Electric Arc Welding Process 電弧焊過程的圖像拍攝和動態處理
- Passive visual sensing method is the major method for sensing welding process, the principle of which is to capture weld pool image by the illumination of electric arc. 被動式視覺傳感方法是焊接過程傳感的一種主要方法，其主要原理是利用電弧光照射熔池表面獲得熔池圖像。
- Such as electric arc welding, carbon dioxide gas shielded arc welding, TIG etc. 如：電弧焊、二氧化碳氣體保護焊、氬弧焊等各種焊接。
- Vibratory submerged arc welding is a new welding process to improve welding quality by applying vibration on plate. 振動埋弧焊工藝是一種在焊接過程中通過給焊件施加振動來改善焊接性能的新工藝。
- Electric arc welding should not be carried out on equipment suspended from a crane because of the risk of damage to lifting wires from uncontrolled stray currents. 不應在懸掛于起重機下的設備上進行電弧焊接，否則有未經控制的雜散電流損壞吊索的危險。
- The results show that the Shielded Metal Arc welding process has a significant effect on the corrosion performance of DSS. 結果表明,手工電弧焊工藝過程對雙相不銹鋼材料的耐點蝕性能具有顯著的影響,點蝕優先發生在焊縫金屬或焊接熱影響區中。
- Surfacing process was conducted by shielded metal arc welding process on 45 steel substrate using electrodes CHR207,CHR227,CHR237 under the same welding conditions. 采用CHR207、CHR227和CHR237堆焊焊條,通過手工電弧焊工藝在45鋼基體上進行堆焊試驗;
- Surfacing process test is made on Q235 steel substrate by shielded metal arc welding process using electrode CHR322 at different welding current condition. 采用焊條電弧焊工藝方法,選用CHR322堆焊焊條在Q235鋼基體上以不同的焊接電流進行了堆焊試驗。
- Using low cost charge coupled device (CCD), a vision sensing equipment in welding process was made, and a real time plasma arc welding (PAW) seam tracking system was implemented. 采用低成本電荷耦合器件制作了焊接過程視覺傳感器,實現了一種等離子弧焊焊縫實時跟蹤系統。
- The system has successfully been in welding large vessel head of missile in order to overcome the longstanding problems of uncontrolled quality as with manual arc welding process. 該系統已成功地用于火箭大型容器封頭的焊接中。效果良好,解決了長期以來手工焊質量難以控制的難題。
- Surfacing process was conducted by shielded metal arc welding process on 45 steel substrate using electrodes CHR207, CHR227, CHR237 under the same welding conditions. 摘要采用CHR207、CHR227和CHR237堆焊焊條，通過手工電弧焊工藝在45鋼基體上進行堆焊試驗；
- For electric arc welding in a space with conductive walls or floors, the welder should be provided with an insulating mat or cradle to avoid bodily contact with the walls. 在安裝有傳導性墻壁或地板的空間進行電弧焊接時，應向焊工提供絕緣墊或支架以避免人體接觸到墻壁。
- Manual electric arc welding runways for cranes 手工電弧焊接起重機運行軌道
- The satisfactory tests of arc-ignition and good properties of welding process may prove this switched MOSFET arc welding power source to be an electronic power source with broad prospects. 利用所研制的開關式場效應管弧焊電源進行引弧試驗和工藝試驗,結果表明,此電源具有良好的引弧性能和工藝性能,是一種發展前景較遠大的電子弧焊電源。
- Lightweight electric arc welding machine 輕便型電弧焊機
- By using manual arc welding to repair the big kiln circle, the welding process of ZG310-570 super thick cast steel piece was a success, with good running effect observed for more than 5 years. 通過對大窯輪圈采用手工電弧焊的方法進行修復,成功地解決了ZG310-570鑄鋼特大厚件的焊接工藝,經過5年多的運行觀察,使用效果良好。
- Lightweight electric arc welding rectifier 輕便型弧焊整流器
- This paper interprets the short-circuit arc welding process and the process stability.The evaluation methods and criteria for the short-circuit arc welding process are introduced and discussed. 簡述了短路電弧焊接的物理過程及過程穩定性概念，介紹了有關短路焊接過程穩定性各種評價方法及相應準則，最后對其進行了必要的討論。
- shielded metal manual electric arc welding 手弧焊
