您要查找的是不是：
- ultimate limit bending moment 極限彎矩
- Based on the orthotropic elastic thin plate theory, the mechanical performance of shear wall subjected to non-planar bending moment acting from the beam was studied. 摘要應用正交各向異性彈性薄板理論分析了鋼筋混凝土剪力墻在框架梁傳遞來的平面外彎矩作用下的力學行為，得到了節點的轉動剛度和墻體有效計算寬度的解析表達式；
- The actual stress is not proportional to the bending moment. 實際上應力與彎矩不成正比。
- But the bending moment at the central hinge must vanish. 但在中間鉸處，彎矩必定為零。
- Objective To investigate the elastic limit and relevant enclasp force of the non-precious metal wrought wire clasp. 目的研究非貴金屬鍛絲卡環的彈性極限及其相應卡抱力。
- The induced bending moment may lead to destructibility of the pipeline. 彎矩的產生可能導致管線的破壞。
- Torsion deformation is the biggest effect factor on elastic limit equivalent stress. 扭轉變形是對鋼絲的彈性極限等效應力情況影響最大的因素。
- When a material is stressed byong the elastic limit a permaent deformation results. 當一種材料的應力超過彈性極限時,就會(huì )產生永久變形。
- The comparison between the test data and Billington experiential formula and ASME code shows that the formula was more accurate to the limit value in the in plane bending moment, and was very suitable for engineering application. 通過試驗數據驗證和與基于A(yíng)SME規范及Billington的經驗公式比較表明 ,該公式對面內彎矩極限值有較高的估算精度 ,具有較大的工程應用價值。
- Objective To investigate the elastic limit and relevant enclasp force of the non-precious metal casting clasp. 目的 研究非貴金屬鑄造卡環的彈性極限及其相應卡抱力。
- Shear force is implicit in the development of bending moments. 桿中的剪力在彎矩的推導中是不明顯的。
- It is revealed that pre-stressing of fibers could effectivelyincrease the elastic limit,yielding strength and fracture strength of VIRALL Iaminates. 結果表明，纖維預拉伸應力能有效地提高VIRALL復合板的彈性極限、屈服強度以及斷裂強度。
- Residual elastic recovery bending moment 殘余彈復彎矩
- ABSTRACT: Objective To investigate the elastic limit and relevant enclasp force of the nonprecious metal wrought wire clasp. 摘要:目的研究非貴金屬鍛絲卡環的彈性極限及其相應卡抱力。
- Stresses beyond its elastic limit cause the material to yield, or flow, and the result is permanent deformation or breakage. 超出彈性極限的應力將引起材料屈服或流變，結果產生永久形變或斷裂。
- This increases both the rigid body rotation of the vehicle and the bending moment. 這既增加了飛行器的剛體轉動，也增加了彎矩。
- In the FEM simulation of the loading identification process, the bending moment maintains a constant amplitude, hut its direction is alterable. 在有限元仿真計算中，彎矩載荷的大小保持不變，但方向可調。
- Within the elastic limit of the material,the relation between the retention of gold alloy clasp and the depth of abutment undercut showed positive correlation. 在卡環彈性極限內,金合金卡環固位力與卡環臂進入基牙倒凹的深度成正比。
- The unique phenomena at any cross section of EULER compressive bar under the zero bending moment is analyzed. 從理論上分析了歐拉壓桿任意截面上彎矩為零的狀態下所出現的奇異現象。
- The paper aims at the maximum axial load,showing that the maximum axial load determined by the shakedown limit is much larger than that by the elastic limit. 本文嘗試著進行一些探討，提出應以鋼軌的安定極限值代替鋼軌的彈性極限值作為鋼軌的許用極限值，并就此進行了理論計算及實驗分析工作，提出了一些有益的結論。
