您要查找的是不是：
- The submarine gate and two stage mold unloading mechanism of cavity plate and ejector pin are adopted in the injection mould. 推出塑件時,先依靠與塑件接觸面積大的型腔板推動塑件,使塑件先與型芯分離,然后推桿將塑件推出型腔。
- Does this part need an ejector pin or an ejector bar? Can we add an ejector blade? 請問產品這個面可否加頂針或頂塊?產品允許加扁頂針嗎?
- Design of vent system includes vent groove,vent plug and clearance of ejector pin. 介紹了熱芯盒模具分型面排氣槽、排氣塞以及推桿間隙排氣等排氣系統設計方法。
- The runner system was ejected by deviating hole and spherical ejector pin automatically. 澆注系統凝料的脫出采用了斜拉孔、球形拉料桿自動脫料機構。
- After mold opening, this pin will function as an ejector pin and ejects the sprue from a sprue bush. Also it releases gas contained in molten plastic. 開模以后，拉料桿像頂針一樣將澆注凝料從澆口套內頂出，同時也釋放融料中的氣體。
- When this sprocket/bearing failed, the retaining plate and bolt with the safety lanyard failed also and this allowed the assembly to drop to the floor. 當這個部位的鏈輪/軸承壞了的時候，用安全繩固定的印版和螺栓也壞了導致整個印機掉在地上。
- HOT RUNNER SYSTEM,TEMPERATURER CONTROLLER. MOLDCOMPONENT（EJECTOR PIN,BLADE EJECTOR.）MULTI-FUNCTION FILTER NOZZLE. HEAT PIPE,OILLESS BEARING. 熱澆道系統、溫度控制器、模具零配件（射梢、強力型）萬能瀘嘴、測溫表、自潤軸承、潤滑柱。
- NOTE: The disc holder should not be removed when servicing only the disc, remove allen head screws holding the disc retaining plate and replace disc. 注意：如果只是維修閥瓣，就不要拆卸閥瓣固定器，只需拆卸支撐閥瓣固定器板的六角頭螺絲和拆卸閥瓣即可。
- The product has excellent tooling quality and machining performance, so as to alleviate and avoid the deformation of ejector pin because of heat treatment. 該產品具有良好易切削性能和機械加工性能，從而避免了薄壁推管（司筒）因熱處理而產生變形。
- When this sprocket/ bearing failed, the retaining plate and bolt with the safety lanyard failed also and this allowed the assembly to drop to the floor. 當這個部位的鏈輪/承壞了的時候，用安全繩固定的印版和螺栓也壞了導致整個印機掉在地上。
- As we know, sheet-pile retaining wall is a common engineering measure, the traditional retaining plate is a vertical plate, so greening measures can not be combined. 樁板墻是整治邊坡中常用的一種工程措施,傳統的擋土板是一種直立式板,無法和綠化措施相結合。
- It's used under the vacuumed condition in the deep and closed molds or when having problems with ejection of ejector pin for the products in large size that has the difficulty in leaving the molds. 氣頂用在有深度，密閉的真空狀態下，在頂針頂出困難時使用，如產品面積大，不容易脫落時，亦可使用。
- Can we add ejector sleeves or ejector pins in the boss of this part? 產品的這個位置不能出模，我們打算做行位，在此面上會(huì )有分模線，你接受嗎?
- Pistons and piston accessories (Piston rings, gudgeon pins，retaining cylinder，liners, etc. 展品：活塞及活塞運動副（帶有活塞環，活塞銷，卡環，缸套等）
- inclined ejector pin at fixed half 定模斜推桿
- Ability to maintain and repair core and ejector pins, die springs, and other material. 具備維護和修理模心、頂出針、模具彈簧等其它配件。
- Keywords Injection mould;side slide;demould;ejector pin; 注塑模;側滑塊;脫模;頂芯;
- Let's pin the notice on the bulletin board. 咱們把這個通知釘在布告牌上吧。
- Introducting a gear billet forming die carrier structure used on friction press for no fash forming discusses die carrier guide ,ejector pins and main elements selection of materials,heat treatment. 介紹了一種在摩壓機上采用無飛邊模鍛齒輪坯的模架結構。對模具的導向、頂料裝置以及主要構件的選材、熱處理進行了論述。
- A dyke was built to retain the floods. 修了一道堤壩擋住洪水。
