您要查找的是不是：
- Hard-nesses are Brinell Hardness Numbers. 硬度是布氏硬度.
- Method of measurement uncertainty evaluation for Brinell hardness test results was introduced in the present work. 文章介紹了布氏硬度試驗中測量結果的不確定度評定方法。
- The brinell hardness and the compressive properties increase with TiN content increasing. 其布氏硬度和壓縮強度隨TiN含量的增加而增大.
- An investigation was made on brinell hardness test with a universal material testing machine. 根據布氏硬度試驗的原理 ,提出一種在萬能材料試驗機上進行布氏硬度試驗的方法。
- The Brinell hardness number of the hot rolled plates varies with measurement on the different batch of the products. 通過對熱軋中厚板在不同深度上進行布氏硬度的測定 ,表明測量深度對硬度的明顯的影響 ,并指出獲得穩定值的必要性。
- Carbide balls are usually recommended for Brinell hardness numbers greater than 500. 在布氏試驗中碳化物質地的球通常在加載500千克以上時使用。
- It is improved on a basis of HBE-3000.It serves to measure the Brinell hardness of ferrous metals, non-ferrous metals. HBE-3000A電子布氏硬度計 Model HBE-3000A Electronic Brinwll Hardness Tester 該硬度計是HBE-3000的改進型，適用于測定黑色金屬，有色金屬的布氏硬度。
- The test results shows that there is a linear relationship between Brinell Hardness and the machinability of cast iron with homogeneous microstructure or tiny carbides. 經測試發現，鑄鐵的組織均勻和碳化物細小時，其布氏硬度與機械加工性能之間呈線性關系。
- It was found that the surface roughness is significant in Brinell hardness testing, but has little influence on Rockwell hardness. 結果表明,表面粗糙度對布氏硬度值有重要影響,而洛氏硬度值與表面粗糙度關系不大。
- In this paper the Brinell hardness of differently hardening titanium under loads 3000Kg HB(3000) and 1500Kg HB(1500) are measured. 本文測試了不同硬度鈦在3000公斤和1500公斤負荷下的布氏硬度值HB_(3000)和HB_(1500)。
- The Rockwell and Brinell hardness of 16 metals were investigated. The effects of surface roughness on the hardness values were discussed. 本文通過對16種金屬材料布氏和洛氏硬度的測試,討論了表面粗糙度對它們的硬度值的影響。
- Basic principle and content in standard ASTM E10-01 standard Test Methods for Brinell Hardness of Metallic Materials were described in this paper. 介紹了ASTM金屬材料布氏硬度試驗方法并與相應的國家標準進行了比較。
- HBE-3000 Electronic Brinell Hardness Tester with 10 steps testing force is able to measure hardness values with each 10 Brinell hardness scales. 電子布氏硬度計具備了10級試驗力，可分別測試布氏硬度的10種標尺。
- The piece of cap is made from high heat-resistant material with good heat capacity, and Brinell hardness number in 180 to 135. 帽件由有良好熱容的高耐熱材料制成，且材料的布里涅爾硬度指數在180到135之間。
- It is improved on a basis of OE-HBE-3000.It serves to measure the Brinell hardness of ferrous metals, non-ferrous metals. 產品用途：該硬度計是OE-HBE-3000的改進型，適用于測定黑色金屬，有色金屬的布氏硬度。
- A modification mas made to a current brinell hardness tester so that it can be used to test hardness of soft material under the condition of F/D 2=15 according to ASTM E10. 通過對現有布氏硬度計結構原理的分析 ,采用添加砝碼的方法滿足了ASTME10中F/D2 值為 15的軟質材料的硬度測試。
- Low temperature aging for die casting Al alloy under appropriate technological condition can increase average strength and Brinell hardness more than 10% and 30% respectively. 對壓鑄鋁合金進行低溫時效 ,在最佳工藝條件下 ,合金的平均拉伸強度提高 10%25 以上 ,布氏硬度提高 30%25以上。
- The influences of the duration of polishing and the coarseness of surfaces on the readings of the Brinell hardness measurement of metallic materials are discussed in this paper. 本文討論拋光時間和表面粗糙度對金屬材料布氏硬度測試數據的影響。
- With an increase in extrusion ratio, the extend of fining grain intensify and the size of grain changes, and hence the yield strength and brinell hardness increase. 隨擠壓比的增大,晶粒細化程度增加;強度、硬度隨擠壓比的增大而增大。
- In the uncertainties of Brinell hardness measurement,the uncertainty of measuring system for Brinell hardness indentation is the main one in error analysis. 為修訂金屬布氏硬度試驗方法國家標準,測定了不同試樣厚度的布氏硬度值。
